Connectors – Important
• Flymo connectors are suitable for use with 2 core
cable only. Under no circumstances should these con-
nectors be used for earthed products.
• All Flymo connectors and cables are of splashproof
construction. They are not waterproof and must not be
left outside permanently nor should they be sub-
merged or immersed in water. Do not let cable lay or
trail through pools of water or splashed with water from
hose pipes.
Mains plug replacement – Important
• If the plug supplied is cut off it should be destroyed.
There is an electric shock hazard if a cut off plug is
inserted into a 13 amp socket.
1. No earth required. Flymo products are double insulat-
ed to EN 60335 and under no circumstances should
an earth be connected to any part of the product.
2. Ensure the mains voltage suits your product.
3. Important! The wires in the mains lead are coloured in
accordance with the following code:
BLUE – NEUTRAL; BROWN – LIVE. The wire which is
coloured BLUE must be connected to the Terminal
which is marked with the letter 'N' or coloured BLACK.
The wire which is coloured BROWN must be connect-
ed to the Terminal which is marked with the letter 'L' or
coloured RED.
4. It is important that the outer sheath is clamped cor-
rectly into the 3-pin plug.
5. If in doubt consult your local Service Repairer or quali-
fied electrician before the machine is used.
6. A 13 Amp fuse must be fitted to the mains plug.
7. The normal plug fuse and household fuse only protect
the electrical equipment and are not a safeguard
against electrocution.
Training
1. Read the instructions carefully. Be familiar with the
controls and the correct use of the machine.
2. Never allow children or people unfamiliar with these
instructions to use the machine. Local regulations can
restrict the age of the operator.
3. Never operate the machine while people, especially
children, or pets are nearby.
4. Keep in mind that the operator or user is responsible
for accidents or hazards occurring to other people or
their property.
Preparation
1. While operating the machine always wear substantial
footwear and long trousers. Do not operate the
machine when barefoot or wearing open sandals.
Avoid wearing clothing that is loose fitting or that
has hanging cords or ties.
2. Thoroughly inspect the area where the machine is to
be used and remove all objects which can be thrown
by the machine.
3. Before using, always visually inspect to see that the
blade, blade bolt and the blade assembly are not
worn or damaged. Replace worn or damaged com-
ponents in set to preserve balance. Replace dam-
aged or unreadable labels.
4. Before use check the supply and extension cord for
signs of damage or aging. If the cord becomes
damaged during use, disconnect the cord from the
supply immediately. DO NOT TOUCH THE CORD
BEFORE DISCONNECTING THE SUPPLY. Do not use
the machine if the cord is damaged or worn.
Operation
1. Operate the machine only in daylight or in good
artificial light.
2. Avoid operating the machine in wet grass.
3. Always be sure of your footing on slopes.
4. Walk, never run.
5. Mow across the face of slopes, never up and down.
6. Exercise extreme caution when changing direction on
slopes.
7. Do not mow excessively steep slopes.
8. Use extreme caution when reversing or pulling the
machine towards you.
9. Stop the blade(s) if the machine has to be tilted for
transportation when crossing surfaces other than
grass, and when transporting the machine to and
from area to be used.
10. Never operate the machine with defective guards or
shields, or without safety devices, for example deflec-
tors and / or grass collector, in place.
11. Switch on the motor carefully according to instruc-
tions and with feet well away from the blade(s).
12. Do not tilt the machine when switching on the motor,
except if the machine has to be tilted for starting.
In this case, do not tilt it more than absolutely neces-
sary and lift only the part, which is away from the
operator.
13. Do not start the machine when standing in front of
the discharge opening.
14. Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
15. Do not transport the machine while the power source
is running.
16. Stop the machine, and remove the plug from the
socket. Make sure that all moving parts have come
to a complete stop
• whenever you leave the machine,
• before clearing blockages or unclogging chute,
• before checking, cleaning or working on the
machine,
• after striking a foreign object. Inspect the machine
for damage and make repairs before restarting and
operating the machine;
if the machine starts to vibrate abnormally
(check immediately)
• inspect for damage,
• replace or repair any damaged parts,
• check for and tighten any loose parts.
Maintenance and storage
1. Keep all nuts, bolts, and screws tight to be sure
the machine is in safe working condition.
5
EN
