background image

SkyRanger Nynja 600 Operators Manual issue 1 

22 

5.5    Takeoff and landing performance   

Take-off and landing performance for short dry grass at 600Kg:  

Variants 

TODR 
(TO Flaps) 

LDR 
(LD Flaps) 

Climb rate 

Vy 

Notes 

Nynja 600 

912ULS 

326m 

(includes 

1.3 factor) 

335m 

840 fpm

 

65 kn 

75 mph 

Approach speed 

57 kn / 65 mph 

 

The following additional safety factors should be applied to the take-
off distance to clear a 15metre obstacle (taken from CAA GA Safety 
information):   

Per 1000 ft runway height above Sea Level 

Multiply by 1.1 

Per 10°C increase in temperature above 15°C 

Multiply by 1.1 

Per 2% uphill slope 

Multiply by 1.1 

Soft ground or snow or wet grass 

Multiply by 1.25+ 

If you have to take-off with a tailwind 

Multiply by 1.2 for every 4 
knots of wind 

Now to be sure, multiply by 1.33, to take into account that you may not fly the aeroplane as 
well as the company test pilot did when he worked out the values in the manual. 

 

The following additional safety factors should be applied to the landing 
distance to clear a 15metre obstacle on the approach (taken from CAA 
GA safety information): 

 

For every 1000ft you are above sea level  

multiply by 1.05 

For every 10

0

C above 15

0

C air temperature 

multiply by 1.05 

For every 2

of downslope 

multiply by 1.1 

If the ground is soft, or there is snow or wet grass 

multiply by 1.25+ 

(very short grass may be more 
slippery – up to 1.6) 

If you have to land with a tailwind 

multiply by 1.2 for every 4 
knots of wind 

Now to be sure, multiply by 1.43, to take into account that you may not fly the aeroplane as 
well as the company test pilot did when he worked out the values in the manual. 

Summary of Contents for SkyRanger Nynja 600































































Reviews: