EN
IMPORTANT SAFETY INSTRUCTIONS
WARNING
– To guard against injury, basic safety precautions should be
observed, including the following:
1.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
and all the important notices on the appliance before using. Failure to do so may
result in loss of fish life and/or damage to this appliance.
2.
WARNING:
This appliance is NOT waterproof and MUST be protected from
coming in contact with water.
3.
DANGER
– To avoid possible electric shock, special care should be taken since
water is employed in the use of aquarium equipment. For each of the following
situations, do not attempt repairs yourself; return the appliance to an authorized
service facility for service or discard the appliance.
A. Carefully examine the appliance after installation. It should not be plugged in if
there is water on parts not intended to be wet.
If the appliance or any part of it
falls into the water DO NOT reach for it. First unplug the unit before retrieving.
B. Do not operate any appliance if it has a damaged cord or plug, or if it is
malfunctioning or it is dropped or
damaged in any manner.
C. To avoid the possibility of the appliance
plug or receptacle getting wet, position
the appliance to one side of a wall mounted
receptacle to prevent water from dripping
onto the receptacle or plug. A “drip loop”
(see illustration) should be arranged by
the user for the cord connecting appliance
to a receptacle. “The drip loop” is that
part of the cord below the level of the
receptacle or the connector if an extension cord is used, to prevent water
travelling along the cord and coming in contact with the receptacle. If the plug
or receptacle does get wet,
DO NOT
unplug the cord. Disconnect the fuse or
circuit breaker that supplies power to the appliance. Then unplug and examine
for presence of water in receptacle.
4. This appliance is not intended for use by persons (including children) with
significantly impaired physical or mental capabilities, unless they have been
given supervision or instruction concerning the use of the appliance by a person
responsible for their safety. Children should always be supervised to ensure that
they do not play with the appliance.
5. To avoid injury, do not touch moving parts or hot parts.
6.
CAUTION
- Always unplug or disconnect all appliances in the aquarium from
electricity supply before placing hands in water, before putting on or taking off
parts and while the equipment is being installed, maintained or handled. Never
yank cord to pull plug from outlet. Grasp the plug and pull to disconnect. Always
unplug an appliance from an outlet when not in use.
7.
FOR INDOOR HOUSEHOLD USE ONLY. DO NOT IMMERSE.
Do not install or
store the appliance where it will be exposed to weather or temperatures below
freezing. Do not install the appliance near filter outputs, heat sources, or expose
it to water spray or humidity. Do not submerge in water.
8. Do not use the appliance for other than intended use. The use of attachments
not recommended or sold by the appliance manufacturer may cause an unsafe
conditions.
9. If an extension cord is necessary, a cord with proper rating should be used. A
cord rated for less amperes or watts than the appliance rating may overheat.
Care should be taken to arrange the cord so that it will not be tripped over or
pulled. The connection should be carried out by a qualified electrical installer.
SAVE THESE INSTRUCTIONS
For the complete use and understanding of this product it is recommended that
this manual is thoroughly read and understood. Failure to do so may result in
damage to this product.
Congratulations on your purchase of the Fluval 2 Channel LED Lamp Timer, which can be programmed
for sunrise, mid-day and dusk settings; mimicking the sun’s natural cycle to create a natural
environment for fish.
INSTALLATION AND USAGE
CAUTION:
Always disconnect the appliances in the aquarium from the electrical supply before any
kind of maintenance or installation is being performed.
The Fluval LED Lamp Timer provides control of up to two channels, which simultaneously operate two
12V lights, two 24V lights, or one 12V and one 24V light. Maximum power per channel is 36W at 12V
and 60W at 24V. The Fluval LED Lamp Timer is compatible with LEDs featuring a standard 2.1 x 5.5 mm
DC plug connection.
• Ensure LED lamp(s) is disconnected from the electrical supply.
• Connect the LED lamp to the male (top) DC connector on the timer.
• Connect the LED transformer (power source) to the female (bottom) DC connector on the timer.
• Connect the transformer plug to the electrical supply.
•
Important:
when connecting the LED lamp and the LED transformer (power source) to the timer,
always ensure that they are connected to the same matching channel (side) as each other.
•
Important note:
If connecting a dimmable LED lamp, ensure that your lights are set to 100%
(maximum output) before connecting it to the timer. This will allow the timer to calibrate the LED
lamp accurately.
