manualshive.com logo in svg

Fluke SMFT-1000, User Manual, Page: 47 / 48

Share
Download
Fluke SMFT-1000 User Manual Download Page 47

Multifunction PV Analyzer

Maintenance

43

Battery Replacement

Replace the batteries with six AA batteries. Alkaline batteries are supplied with the Tester.

XW

 Warning

To prevent possible electrical shock, fire, or personal injury:

Remove the test leads and any input signals before you replace the battery.

Install ONLY specified replacement fuses with the amperage, voltage, and 

interrupt ratings shown in the 

Specifications

 section of this manual.

To replace the batteries (see 

Figure 3

):

1. Push 

 to turn off the PV Analyzer.

2. Remove the test leads from the terminals.
3. To remove the battery door, use a standard-blade screwdriver to turn the battery door 

screws (x3) one-quarter turn counterclockwise.

4. Push the release latch and slide the battery holder out of the Tester.
5. Replace the batteries.
6. Replace the battery holder and the battery door.
7. Turn the battery door screws one-quarter turn clockwise to fasten the door.

Figure 3. Battery Replacement

W

 FF 630 mA 

1000 V IR 30 kA

Shop for Fluke products online at:

1.888.610.7664

www.

MyFlukeStore

.com

Summary of Contents for SMFT-1000

















































Reviews:

No comments