manualshive.com logo in svg

Fluke SMFT-1000, User Manual, Page: 45 / 48

Share
Download
Fluke SMFT-1000 User Manual Download Page 45

Multifunction PV Analyzer

Maintenance

41

Figure 2. IR Serial Cable Attachment

3. At the PC, open the TruTest software program.
4. Turn on the PV Analyzer.
5. See the 

TruTest™ Data Management Software

 documentation for complete instructions 

on how to set the date/time stamp and upload data from the PV Analyzer.

Download PV Model Data

See the 

TruTest™ Data Management Software

 documentation for complete instructions on 

how to download the PV Model data.

Maintenance

XW

 Warnings

To prevent possible electrical shock, fire, or personal injury:

Be sure that the battery polarity is correct to prevent battery leakage.

Repair the Product before use if the battery leaks.

Have an approved technician repair the Product.

Use only specified replacement parts.

Replace a blown fuse with exact replacement only for continued protection 

against arc flash.

Do not operate the Product with covers removed or the case open. Hazardous 

voltage exposure is possible.

Remove the input signals before you clean the Product.

IR Serial Cable

IR Port

IR Port

IR Serial Cable

Shop for Fluke products online at:

1.888.610.7664

www.

MyFlukeStore

.com

Summary of Contents for SMFT-1000

















































Reviews:

No comments