manualshive.com logo in svg

Fluidwell F014-P, Manual

Share
Download
Fluidwell F014-P Manual Download Page 40

Page 39 

FW-F014-P-M_v0402_05_EN.docx 

 

PROBLEM SOLVING 

In this appendix, several problems are included that can occur when the F014-P is going to be 
installed or while it is in operation. 

 

Flowrate displays "0 / zero" while there is flow (total is counting): 

Check: 

•

 

SETUP 22 / 25: are the K-Factor time unit correct? 

 

The pass code is unknown: 

If the pass code is not 1234, there is only one possibility left: call your supplier. 

 

ALARM 

When the alarm flag starts to blink an internal alarm condition has occurred. Press the "select 
button" several times to display the 4-digit error code. The codes are: 

 

•

 

0001:  
irrecoverable display-data error: data on the display might be corrupted. 

•

 

0002:  
irrecoverable data-storage error: the programming cycle might have gone wrong: check 
programmed values. 

•

 

0003: 
error 1 and error 2 occurred simultaneously 

 

The alarm condition will almost certainly be handled internally and if all mentioned values still appear 
correct, no intervention by the operator is needed. If the alarm occurs more often or stays active for 
a longer time, please contact your supplier. 
 

 

Summary of Contents for F014-P













































Reviews:

No comments

Brands by name

Popular brands

Load more brands