background image

MN16  V1.2    7/08 

14 

Warranty 

EXTECH INSTRUMENTS CORPORATION warrants the basic instrument to be free of 
defects in parts and workmanship for three years from date of shipment (a six month limited 
warranty applies on sensors and cables). If it should become necessary to return the 
instrument for service during or beyond the warranty period, contact the Customer Service 
Department at (781) 890-7440 EXTENSION 210 for authorization or visit www.extech.com for 
more information. 

A Return Authorization (RA) number must be issued before any 

product is returned to Extech.

 The sender is responsible for shipping charges, freight, 

insurance and proper packaging to prevent damage in transit. This warranty does not apply to 
defects resulting from action of the user such as misuse, improper wiring, operation outside of 
specification, improper maintenance or repair, or unauthorized modification. Extech 
specifically disclaims any implied warranties or merchantability or fitness for a specific 
purpose and will not be liable for any direct, indirect, incidental or consequential damages. 
Extech's total liability is limited to repair or replacement of the product. The warranty set forth 
above is inclusive and no other warranty, whether written or oral, is expressed or implied. 

 

Calibration

 

and Repair Services

 

Extech offers repair and calibration services for the products we sell. Extech also provides 
NIST certification for most products. Call the Customer Care Department for information on 
calibration services available for this product. Extech recommends that annual calibrations be 
performed to verify meter performance and accuracy. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Copyright 

©

 2008 Extech Instruments Corporation (a FLIR company) 

All rights reserved including the right of reproduction in whole or in part in any form.

 

 

Support line (781) 890-7440 

Technical Support: Extension 200; E-mail: [email protected] 

Repair & Returns: Extension 210; E-mail: [email protected] 

Product specifications subject to change without notice 

For the latest version of this User’s Guide, Software updates, and other up-to-the-minute 

product information, visit our website: www.extech.com 

Extech Instruments Corporation, 285 Bear Hill Rd., Waltham, MA 02451 

Summary of Contents for Extech Instruments MN16















Reviews: