background image

MN16  V1.2    7/08 

TEMPERATURE MEASUREMENTS 

1. 

Set the function switch to the 

ºF

 or 

ºC

 position. 

2. 

Insert the Temperature Probe into the input jacks, making sure to 
observe the correct polarity. 

3. 

Touch the Temperature Probe head to the part whose temperature you 
wish to measure. Keep the probe touching the part under test until the 
reading stabilizes (about 30 seconds). 

4. 

Read the temperature in the display. 

 

Note:

 The temperature probe is fitted with a type K mini connector. A mini 

connector to banana connector adaptor is supplied for connection to the 
input banana jacks. 

 
 
 
 

CAPACITANCE MEASUREMENTS 

WARNING:

 To avoid electric shock, disconnect power to the unit under test and 

discharge all capacitors before taking any capacitance measurements. Remove the 
batteries and unplug the line cords. 

1. 

Set the rotary function switch to the 

CAP

 position. 

2. 

Insert the black test lead banana plug into the negative 

COM

 jack. 

Insert the red test lead banana plug into the positive 

CAP

 jack. 

3. Press 

the 

MODE

 button to indicate “

nF

” on the display. 

4. 

Touch the test leads to the capacitor to be tested. 

5. 

Read the capacitance value in the display 

 
 

 
 
 
 

 

FREQUENCY/DUTY CYCLE MEASUREMENTS  

1. 

Set the rotary function switch to the “

Hz %

” position. 

2. 

Press the MODE button to indicate “

Hz

” in the display. 

3. 

Insert the black lead banana plug into the negative 

COM

 jack 

Insert the red test lead banana plug into the positive 

Hz

 jack. 

4. 

Touch the test probe tips to the circuit under test. 

5. 

Read the frequency on the display. 

6. Press 

the 

MODE

 button again to indicate “

%

” on the display. 

7. 

Read the % of duty cycle on the display. 

 
 
 
 
 
 

Summary of Contents for Extech Instruments MN16















Reviews: