background image

—5—

General Safety Rules

Signal words:

“DANGER” indicates an imminently hazardous 

situation which, if not avoided, will result in 

death or serious injury. The signal word is 

limited to the most extreme situations.

“WARNING” indicates a potentially hazardous 

situation which, if not avoided, could result in 

death or serious injury.

“CAUTION” indicates a potentially hazardous 

situation which, if not avoided, may result in 

minor or moderate injury. It may also be used to 

alert against unsafe practices.

Safety Symbol

!

This international safety symbol is used to 

identify and call attention to specific  

safety matters.

Safety Information

To Avoid Severe Personal Injury or Property 

Damage, read carefully and understand the 

following Safety Precautions.

1. WORK AREA

!

CAUTION

Keep your work area clean and well lit. Cluttered 

benches and dark areas invite accidents.

2. PERSONAL SAFETY

!

WARNING

Stay alert, watch what you are doing and use 

common sense when operating a tool. Do not 

use tool while tired or under the influence of 

drugs, alcohol, or medication. A moment of 

inattention while operating tools may result in 

serious personal injury.

Dress properly. Do not wear loose clothing 

or jewelry. Contain long hair. Keep your hair, 

clothing, and gloves away from moving parts. 

Loose clothes, jewelry, or long hair can be 

caught in moving parts.

Do not overreach. Keep proper footing and 

balance at all times to enable better control of 

the tool in unexpected situations.

Never alter or remove safety devices.

Keep your hands and fingers away from the 

knives in the punchboard, at all times.

!

CAUTION

Use safety equipment. Always wear eye 

protection. Dust mask, non-skid safety shoes, 

hard hat, or hearing protection must be used for 

appropriate conditions.

  –Save  These  Instructions–

Summary of Contents for Novitool PUN M 300













































Reviews: