background image

27

Section 10 - Other Flexco Conveyor Products

Flexco® provides many conveyor products that help your conveyors to run more efficiently and safely. 

These components solve typical conveyor problems and improve productivity.   

Here is a quick overview on just a few of them:

•  Patented ConShear™ blade renews its cleaning edge as it 

wears

•  Visual Tension Check™ for optimal blade tensioning and 

simple retensioning

•   Quick and easy one-pin blade replacement Material Path 

Option™ for optimal cleaning and reduced maintenance

EZS2 Secondary Cleaner

•  Patented “pivot & tilt” design for superior training action
•  Dual sensor rollers on each side to minimize belt damage
•  Pivot point guaranteed not to freeze or seize up
•  Available for topside and return side belts

•  Exclusive Velocity Reduction Technology™ to better protect 

the belt 

•  Slide-Out Service™ gives direct access to all impact bars for 

change-out

•  Impact bar supports for longer bar life
•  4 models to custom fit to the application

•  A belt cleaner for the tail pulley
•  Exclusive blade design quickly spirals debris off the belt
•  Economical and easy to service
•  Available in vee or diagonal models

PT Max™ Belt Trainer

DRX™ Impact Beds

Belt Plows

•  Long-wearing tungsten carbide blades for superior cleaning 

efficiency

•  Patented FormFlex™ cushions independently tension each 

blade to the belt for consistent, constant cleaning power

•  Easy to install, simple to service
•  Works with Flexco mechanical belt splices

•  “Limited space” cleaners for tight conveyor applications
•  High Temp cleaners for severe, high heat applications
•  A rubber fingered cleaner for chevron and raised rib belts
•  Multiple cleaner styles in stainless steel for corrosive 

applications

Flexco Specialty Belt Cleaners

EZP1 Precleaner

Summary of Contents for MMP Precleaner





























Reviews: