Flex innovations Cessna 170 60E G2 Instruction Manual Download Page 4

3

86.7 in. (2204mm)

60.1

 in. (15

44mm)

9lb. 3oz. (4171g) 

RTF with 6S 5200

mAh motor battery &

Potenza 60 Light 540 KV 
Brushless Motor (FPZM1060L)

Potenza 100A ESC with Internal 
8A BEC (FPZE100ABEC)

Potenza DS34 Digital Metal Gear 
Mini Servo (FPZDS34)

Aura 8 Advanced Flight Control 
System (FPZAURA08)

16 x 6 Electric SR Propeller 
(FPMP1606E)

NEEDED TO 
COMPLETE

4200-6200mAh 6S 22.2V 40C+ 
LiPo  (FPZB42006S40, 
FPZB52006S40, FPZB62006S40)

NEEDED TO 
COMPLETE

6+ Channel Computer 
Transmitter

NEEDED TO 
COMPLETE

RECEIVER 

Serial-Capable Receiver

SPECIFICATIONS

REPLACEMENT PARTS LISTING

FPM4470

Cessna 170 60E G2: Super PNP Orange

FPM4480

Cessna 170 60E G2: Super PNP Night Orange

FPM447001

Cessna 170 60E G2: Fuselage Orange

FPM44801

Cessna 170 60E G2: Fuselage Orange Night

FPM447002R

Cessna 170 60E G2: Right Wing Panel Orange

FPM447002L

Cessna 170 60E G2: Left Wing Panel Orange

FPM448002R

Cessna 170 60E G2: Right Wing Panel Orange 
Night

FPM448002L

Cessna 170 60E G2: Left Wing Panel Orange Night

FPM447003

Cessna 170 60E G2: Tail Set Orange

FPM447004

Cessna 170 60E G2: Hatch Set / Cowling Orange

FPM447006

Cessna 170 60E G2: Main Wheel Set Black Hub

FPM447008

Cessna 170 60E G2: Pushrod Set

FPM447009

Cessna 170 60E G2: Hardware Set

FPM447011

Cessna 170 60E G2: Orange Decal Set

FPZE100ABEC

Potenza 100A ESC w/8A BEC

FPZM1060L5

Potenza 60L Motor 8mm Shaft w/Collar

FPZM1060L4

Potenza Bearing Set 60L 8mm

FPM447014

Cessna 170 60E G2: Float Set & Struts w/ LED Light 
Orange

FPM447015

Cessna 170 60E G2: Leading Edge Slat Set Orange

FPM447007

Cessna 170 60E G2: Leading Edge Slat Set Red/
Gold

FPM447018

Cessna 170 60E G2: Landing Gear Mount

FPM3170141

Cessna 170 60E G2: Float Set Water Rudder Parts

FPM317007

Cessna 170 60E G2: Tube Joiner Set

FPM317008

Cessna 170 60E G2: Wing Strut Set

FPM317012

Cessna 170 60E G2: Spinner

FPM317013

Cessna 170 60E G2: Main Scale Wheel Set

FPZDS34

Potenza DS34 Digital Metal Gear Mini Servo

FPZDS15F

Potenza DS15 MG Digital Sub-Micro Servo (Floats)

FPZM1060L

Potenza 60 Light 540 KV Brushless Motor

FPZM10603D2

Potenza 60L, 60 3D, 65 3D, 70 Motor X- Mount w/
Screws

FPZM1060L1

Potenza 60L Motor Bolt-on Adapter

FPM317016

Cessna 170 60E G2: Snow Ski Set

FPM317017

Cessna 170 60E G2: Glider Tow Pushrod

FPZA1016

Potenza Advanced R/C LED Controller (6s)

OPTIONAL ITEMS

FPM447014

Cessna 170 60E G2: Float Set & Struts w/ LED 
Light Orange

FPM317020

Cessna 170 60E: Wing Bag Set

FPZB42006S40

Potenza 6S 4200mAh 40C Li-Po Battery

FPZB52006S40

Potenza 6S 5200mAh 40C Li-Po Battery

FPZB62006S40

Potenza 6S 6200mAh 40C Li-Po Battery

ISDTD2

ISDT D2 200W AC/DC Charger

FPZA1010

Potenza Digital Battery Analyzer

SPM4651T

DSMX SRXL2 Serial Telemetry Receiver

FUTT6K

Futaba T6K Transmitter with R3006SB Rx Mode 2

FUTR2001SB

Futaba R2001SB SFHSS S-Bus

FPM317016

Cessna 170 60E: Snow Ski Set

FPM317017

Cessna 170 60E: Glider Tow Pushrod

COMPLETION ITEMS

INST

ALLED!

INST

ALLED!

INST

ALLED!

INST

ALLED!

INCL

UDED!

       WARNING

FOLLOW ALL INSTRUCTIONS PROVIDED BY YOUR BATTERY AND 

CHARGER MANUFACTURER. FAILURE TO COMPLY CAN RESULT IN FIRE.

The assembly of the Cessna 170 60E G2 can be accomplished in less than 

one 

hour.

 Prior to assembling the airplane, it is advisable to charge your battery so 

that you are ready to begin setup upon completion of the assembly of your 
model.  

We recommend the use of an advanced Li-Po balancing charger, such as the 
ISDT D2 Dual 100W Multi Chemistry AC/DC balancing charger for your batteries 
to get the maximum performance and lifespan from them. 

Our airplanes are designed around our Potenza LiPo batteries, and we 
recommend the Potenza 6S 5200mAh 40C LiPo in the Cessna 170 60E G2 based 
on our extensive testing and development. These batteries feature an EC5 
connector, so no soldering is required for use in your Cessna 170 60E G2. 

All are available online at www.flexinnovations.com and your local Flex 
Innovations retailer.

SPECIFICATIONS

Recommended battery – 6S 4200mAh-6200mAh 40C+ Li-Po

BATTERY CHARGING GUIDELINES

Summary of Contents for Cessna 170 60E G2





























Reviews: