Flavel RENOIR RC Installation, Maintenance & User Instructions Download Page 10

Page: 10 / 54

2.2.6

Closure plate fitting

2.2.7

Fit the closure plate to the fireplace opening and ensure that it has a flat

sealing area of at least 10mm sealed on all sides. See figure 3 below

Dimensions stated are for closure plate supplied

Check the operation of the chimney as follows:-

Apply a smoke match to the flue spigot opening in the closure plate and observe

the smoke. If there is a definite flow into the opening then proceed with the instal-

lation. If there is not a definite flow into the opening, pre-heat the chimney for

about two minutes and retest for flow. If there still is no definite flow into the open-

ing, the chimney may require attention. DO NOT FIT THE FIRE-SEEK EXPERT

ADVICE.

Minimum 10mm

Flat Sealing Area

Spigot Opening

168 x 68mm

660mm

460mm

462mm to

CTR

525mm Minimum

650mm Maximum

Fireplace

Opening

Dimensions

Closure

Plate

Dimensions

Air Relief Openings

Fig. 3

305mm Minimum

440mm Maximum

100mm

15mm

Summary of Contents for RENOIR RC























































Search results

Summary of Contents for RENOIR RC

Reviews:

Related manuals for RENOIR RC

Brands by name

Popular brands

Flavel RENOIR RC, Installation, Maintenance & User Instructions

Search results

Summary of Contents for RENOIR RC

Reviews:

Related manuals for RENOIR RC

Brands by name

Popular brands