manualshive.com logo in svg

Flavel RENOIR RC, Installation, Maintenance & User Instructions

Share
Download
Flavel RENOIR RC Installation, Maintenance & User Instructions Download Page 54

Due to our policy of continual improvement and development the exact

accuracy of descriptions and illustrations cannot be guaranteed.

Part No. B-178940

Issue 3

BFM Europe Ltd

Trentham Lakes

Stoke-on-Trent

Staffordshire

ST4 4TJ

www.bfm-europe.com

Telephone - General Enquiries :

(01782) 339000

Telephone - Service :

(0844) 7700169 or (01782) 339008

TROUBLE SHOOTING ADVICE FOR REMOTE CONTROL MODELS PRIOR

TO REQUESTING A SERVICE CALL

Please locate the Indicator light on the control valve, located behind the fender at the

right hand side of the fire (see figure 5 & 6 on page 40), if it shows 

any

of the following

flashing sequences then the problem requires the batteries in the control valve and / or

handset changing, 

be advised that service calls as a result of batteries requiring

being changed in the product or handset are chargeable.

a)

If the red indicator light flashes 

ONCE

every ten seconds the batteries in the 

control valve require changing, see section 5.4

b)

If the red indicator light flashes 

TWICE

every ten seconds the batteries in the 

handset require changing, see section 5.4

c)

If the red indicator light flashes 

THREE

times every ten seconds the batteries in 

the control valve and the handset require changing, see section 5.4

If these red indicator light flashes are ignored then eventually this will show as a flash

every second and your fire will cease to operate until the batteries are changed.

If a permanent red indicator light is shown after attempting to ignite the fire this signifies

no spark or no gas at the pilot and therefore a service call will be required to diagnose

the fault.

PLEASE ENSURE THIS ADVICE IS FOLLOWED TO AVOID BEING CHARGED FOR A

SERVICE CALL AS A RESULT OF BATTERIES REQUIRING TO BE CHANGED. 

Summary of Contents for RENOIR RC























































Reviews:

No comments

Brands by name

Popular brands

Load more brands