background image

SPECIALIZED

HEALTHY

AIR SOLUTIONS

WWW.SEMCOHVAC.COM

ASCENDANT IOM  /  2021.09.12

Ascendant Owner’s Manual - FlaktGr

oup Semco 2021-12

To learn more about FläktGroup 
SEMCO offerings and to contact your 
nearest representative please visit 

www.semcohvac.com

© Copyright 2021 SEMCO LLC. All Rights Reserved. SEMCO embraces a policy of continuous development and improvement, the right is reserved to supply products which may differ from those illus-

trated and described in this publication. Specifications are subject to change without further notice. Any FläktGroup SEMCO purchase is subject to FläktGroup SEMCO standard terms and conditions. 

Certified dimensions will be supplied upon request on receipt of order. SEMCO is a registered Trademark of SEMCO LLC. Other trademarks and logos in this publication may be property of SEMCO, LLC, 

its subsidiaries or any of its related companies and/or other organizations or individuals. 

FläktGroup SEMCO delivers smart, energy-efficient, air-quality solutions to 

support every building application. We offer our customers innovative 

technologies, high-quality products and outstanding performance 

supported by more than fifty years of accumulated industry experience. 

The broadest offering on the market and a strong market presence in 65 

countries worldwide guarantees that we are always by your side, ready 

to deliver: Excellence in Solutions.

FläktGroup SEMCO

Corporate Headquarters

1800 East Pointe Drive 

Columbia, Missouri 65201  USA
573.443.1481
[email protected]

Summary of Contents for SEMCO Ascendant
















Reviews: