background image

11

“INCLINE (3,6,9,12) ”, Adjust the incline quickly.

Left Handrail Button: Incline adjustment button. 

Right handrail button: Speed adjustment button.

Notice: When any button is pressed, it will be accompanied by a prompt tone. When the button is 

adjusted for parameter overrun, it will be accompanied by a long tone prompt. There is no beep 

when the button is pressed Invalid.

COMPUTER OPERATION GUIDE

4. MAIN FUNCTION

Open the power switch, the screen window will light up, the machine will enter into standby state. 
4.1. START-UP QUICKLY (MANUAL):

Put safety key, press ‘ START’ button, the treadmill will run at the lowest speed in 3 seconds, 

press SPEED+/- to adjust the speed. Press /- to adjust the incline. Press the ‘ STOP’ 

button or take out the safety key directly to stop the treadmill.
4.2. COUNT DOWN MODE:

Press the ‘ MODE’ button, you can choose time countdown mode, distance count down mode, 

calories countdown mode, and the screen window will show the default data and glitter. At the 

same time, press SPEED+/- and /- to set the data. Press ‘ START ’ button, the machine 

will run at the lowest speed, you can press SPEED+/- to change the speed, press /- to 

change the incline. When it counts down to 0, the machine will stop smoothly. Certainly, you can 

press ‘ STOP’ button or take out the safety key from the computer to stop the machine.
4.3. INNER INSTALL PROGRAM:

Press ‘PROG’ button to choose the inner install program from P1----P15. When set the program, 

the time window will show default data and glitter, press SPEED+/- or /- button to set 

the running time. Each program has been divided into 16 section, Each exercise time=the setting 

time/16. Press ‘START’, the machine will run at the first section speed and incline date. When the 

section is over, it will enter into next section automatically, the speed and incline will change as 

next section data. When finish one program, the machine will stop smoothly. During the running, 

you can change the speed and incline by the SPEED+/- and /- or Left/right Handrail 

Button. When the program enter next section will come back to the default date. And you can 

press ‘STOP’ or take out the safety key to stop the machine whenever.

At the end of the program mode the treadmill will flash with 15 beeps, after which all data will be 

cleared to 0 and come into standby status.

Summary of Contents for TF-D6501


























Reviews: