Lit. No. 48685, Rev. 00
3
February 15, 2010
49900
Scoop/Retract Blade Position
Moving the control lever from center position toward
the word SCOOP or RETRACT (VEE) on the face of
the control body will cause both wings to move at the
same time into the following blade positions:
Wing Positions
Moving the control lever from center position toward
the word WING or WING IN/OUT on either side of the
face of the control body will cause either wing to move
independently of the other as described below.
Function
Description of Operation
SCOOP
Move control lever toward the word SCOOP
on control face to extend both wings forward
into scoop position. Function times out after
5.5 (XLS) or 5.0 seconds (XtremeV).
RETRACT
Move control lever toward the word RETRACT
(VEE) on control face to draw both wings into the
fully retracted (vee) position. Function times out
after 4.5 (XLS) or 3.0 (XtremeV).
The SECURITY GUARD™ System
Activation & Establishing a 4-Digit Security Code
NOTE: The snowplow must be attached to the
vehicle, and all the electrical connections must
be connected prior to activating the security code
function.
1. Turn the vehicle ignition switch to the "ON" or
"ACCESSORY" position. (It is not necessary to
start the vehicle.)
2. Verify the control power indicator is OFF. If the
power indicator light is red, the control is ON. Slide
the ON/OFF switch to "OFF" to turn the control
OFF.
3. To activate the SECURITY GUARD mode,
move the control lever into the #1 position four
consecutive times, and then in the direction of the
#4 position four consecutive times (sequence:
1, 1, 1, 1, 4, 4, 4, 4). The green FLOAT light will
fl
ash quickly and the red POWER light will turn
ON indicating the system is ready to accept your
4-digit security code.
Enter your 4-digit security code by moving the
control lever into the position of any of the eight
following positions: UP, DOWN, LEFT, RIGHT,
1, 2, 3 or 4.
Once you have entered your 4-digit security
code, the FLOAT light will stop
fl
ashing and the
POWER light will turn OFF. This indicates that
your 4-digit security code is entered and stored in
the SECURITY GUARD system.
4. Once a 4-digit security code is established and
the plow/vehicle electrical connection are lost/
disconnected, the SECURITY GUARD system will
recognize any control that has been programmed
with the same 4-digit security code. Any control
not programmed with the correct 4-digit security
code will require the user to enter the established
security code before activating the snowplow (see
the Manual Unlock procedure).
NOTE: If the control POWER switch is turned ON
prior to completing the programming procedure,
your 4-digit security code will be cancelled.
Function
Description of Operation
L WING &
WING IN/
OUT
Move control lever toward the left side of
LOWER
on the control face to move the left
wing. The
fi
rst time lever is moved into slot
after control is turned ON, or another function
is used, wing will extend. Repeated use of
the lever in the same slot, without using
another function, results in movement in
opposite direction from previous movement.
Function times out after 3.25 (XLS – IN),
3.75 (XLS – OUT), or 3.0 (XtremeV).
R WING &
WING IN/
OUT
Move control lever toward the right side of
LOWER
on the control face to move the
right wing. The
fi
rst time lever is moved into
slot after control is turned ON, or another
function is used, wing will extend. Repeated
use of the lever in the same slot, without
using another function, results in movement in
opposite direction from previous movement.
Function times out after 3.25 (XLS – IN),
3.75 (XLS – OUT), or 3.0 (XtremeV).
