background image

9

Swing Frame Assembly

Retainer with Lock Nut

•  Fit a retainer with lock nut onto the end of the screw and to the 

seat tube support.

Hint:

 A lock nut has been factory assembled to the retainer. 

During shipment, the lock nut may have fallen out of the retainer. 
If it has, please fit it into the hexagonal hole in the retainer so that 
the rounded side of the lock nut faces out.

•  Tighten the screw using the assembly tool. Turn the tool 

clockwise to tighten.

•  Repeat this procedure to fasten the screw in the other seat tube 

and seat tube support, using the remaining retainer with lock nut.

9

10

•  Loosen the screws in the battery compartment door and remove 

the battery compartment door. 

•  Insert four “D” (LR20) 

alkaline

 batteries into 

the battery compartment. 

•  Replace the battery compartment door and tighten the screws.

Hint: 

We recommend using

 alkaline 

batteries for longer

battery life.
•  If this product begins to operate erratically, you may need to reset 

the electronics. Slide the power switch off and then back on.

Battery Compartment

1,5V x 4

“D” (LR20)

Battery Installation

Battery Safety Information
In exceptional circumstances, batteries may leak fluids that 
can cause a chemical burn injury or ruin your product. To avoid 
battery leakage:

•  Do not mix old and new batteries or batteries of different types: 

alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).

•  Insert batteries as indicated inside the battery compartment.
•  Remove batteries during long periods of non-use. Always remove 

exhausted batteries from the product. Dispose of batteries safely. 
Do not dispose of product in a fire. The batteries inside may 
explode or leak.

•  Never short-circuit the battery terminals.
•  Use only batteries of the same or equivalent type as recommended.
•  Do not charge non-rechargeable batteries.
•  Remove rechargeable batteries from the product before charging.
•  If removeable, rechargeable batteries are used, they are only to 

be charged under adult supervision.

•  Protect the environment by not disposing of this product 

with household waste (2002/96/EC). Check your local 
authority for recycling advice and facilities (Europe only).

Summary of Contents for P6946

















Reviews: