background image

2

To prevent injury or death from 
falls or being strangled in the 
restraint system

• Never leave child unattended. 

When used as a Swing:

• Always use the restraint system.
• Never use with an active child who may 

be able to climb out of the product.

When used as an Infant Seat 
or Rocker:

• 

Fall Hazard

 - It is dangerous to use 

this product on an elevated surface. 
Use only on a floor.

• 

Suffocation Hazard

 - Never use on 

a soft surface (bed, sofa, cushion) 
since the product can tip over and 
cause suffocation in soft surfaces.

• Always use the restraint until child 

is able to climb in and out of the 
product unassisted.

• Never use as a carrier. Never use the 

toy bar as a handle.

• Infant seat and swing modes not 

recommended for children who 
can sit up by themselves (6 months 
approximately, until 9 kg/20 lbs).

• Use the Rocker position only when 

child has developed enough upper 
body control to sit without 
leaning forward.

WARNING

Consumer Information

• 

IMPORTANT! PLEASE KEEP THESE INSTRUCTIONS 
FOR FUTURE REFERENCE, AS THEY CONTAIN 
IMPORTANT INFORMATION.

•  Please read these instructions before assembly and use of 

this product. 

•  Adult assembly is required. Tools needed for assembly: 

Phillips screwdriver (not included) and assembly tool (included).

•  Requires four “D” (LR20) 

alkaline

 batteries (not included) for 

swing operation.

•  In Swing mode, only to be used by children that cannot climb 

out of seat.

•  In Infant Seat and Rocker mode, designed for use with children 

from birth to 9 kg (20 lbs).

•  In Rocker mode, always use restraint until your child is able to 

climb in and out of the chair unassisted.

•  Product features and decoration may vary from photos.

Great Britain:

 Vanwall Business Park, Maidenhead SL6 4UB.

Helpline: 01628 500303. www.service.mattel.com/uk.

Australia:

 Mattel Australia Pty. Ltd., 658 Church Street, 

Locked Bag #870, Richmond, Victoria 3121 Australia. 
Consumer Advisory Service 1300 135 312.

New Zealand:

 16-18 William Pickering Drive, Albany 1331, Auckland.

Asia:

 Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, 

Harbour City, Tsimshatsui, HK, China.

Malaysia:

 Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd. (993532-P) 

Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country 
Resort, 47410 PJ. Tel: 03-78803817, Fax: 03-78803867.

Summary of Contents for P6946

















Reviews: