background image

E-16 

 

No volume amplification 

 

Check to see if the VOLUME BOOST INDICATOR  is “

O

N”. The red  LED on the left side of the +40dB 

VOLUME BOOST BUTTON should light. 

 

Check the AC Adaptor and make sure it is properly plugged into the ac power outlet and into the DC JACK 
on the phone. 

 

Noise, Static, Interferences while using the handset 

 

A filter may be required for homes with DSL line or near Radio towers. 

 

There is a red light that continues to flash 

 

You have un-reviewed Caller ID / Call Waiting information or missed a call. 

 

Caller ID information does not show 

 

Make sure you have subscribed to Call

er ID service through your local phone 

company. 

 

No Caller ID information while on a call (Type II Caller ID) 

 

This telephone does not support Type II Caller ID feature and therefore it cannot display the Caller ID of the 
second caller. 

 
 

THE FCC WANTS YOU TO KNOW: 

CONSUMER INFORMATION 

If requested by the telephone company, inform them as follows: 
FCC Registration No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

 

DYFTE12BCID50T

   

Ringer Equivalence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

 

1.2B

 

The particular telephone line to which the equipment is connected. 

 
This equipment complies with 

P

art 68 of the FCC rules and the requirements adopted by the ACTA. 

O

n the 

bottom of this equipment is a label that contains, among other information, a product identifier  of US: 

DYFTE12BCID50T

. If requested,  this number must be provided to the telephone company. An applicable 

certification jacks Universal Service 

O

rder Codes (US

O

C) for the equipment is provided (i.e., RJ11C) in the 

packaging with each piece of approved terminal equipment   
The REN is useful to determine the quantity of devices you may connect to your telephone line and still have all of 
those devices ring when your telephone number is called. In most, but not all areas, the sum of the REN’s of all 
devices connected to one line should not exceed  five (5.0). To be certain of the number of devices you may 
connect to your line, as determined by the REN, you should contact your local telephone company to determine 
the maximum REN for your calling area.

 

If your telephone equipment 

SFA3800

  causes harm to the telephone network, the telephone company may 

discontinue your service temporarily. If possible, they will notify you in advance. But if advance notice isn’t 
practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with the 
FCC. 
Your telephone company may make changes in its facilities, equipment, operations, or procedures that could 
affect the proper functioning of your equipment. If they do, you will be notified in advance to give you an 
opportunity to maintain uninterrupted telephone service. If you experience trouble with this telephone equipment 
disconnect from the network until the problem has been corrected or until you are sure that the equipment is not 
malfunctioning. 
This equipment may not be used on coin service provided by the telephone company. Connection to party lines is 
subject to state tariffs. This equipment is hearing aid compatible. 

NOTICE:

  If your home has  specially wired alarm equipment connected to the telephone line, ensure  the 

installation of this (equipment ID if any) does not disable your alarm equipment. If you have questions about what 
will disable alarm equipment, consult your telephone company or a qualified installer. 

WARNING:

 Changes or modifications to this unit not expressly approved by the party responsible for compliance 

could void the user’s authority to operate the equipment. 
 

 

Summary of Contents for SFA3800





















Reviews: