background image

30

NOTICE

When Fireye products are combined with equipment manufactured by others and/or integrated into sys-
tems designed or manufactured by others, the Fireye warranty, as stated it its General Terms and Condi-
tions of Sale, pertains only to the Fireye products and not to any other equipment or to the combined
system or its overall performance.

WARRANTIES

FIREYE guarantees for 

one year from the date of installation or 18 months from date of manufacture 

of its

products to replace, or, at its option, to repair any product or part thereof (except lamps and photocells)
which is found defective in material or workmanship or which otherwise fails to conform to the descrip-
tion of the product on the face of its sales order. 

THE FOREGOING IS IN LIEU OF ALL OTHER

WARRANTIES AND FIREYE MAKES NO WARRANTY OF MERCHANTABILITY OR ANY
OTHER WARRANTY, EXPRESS OR IMPLIED.

 Except as specifically stated in these general terms

and conditions of sale, remedies with respect to any product or part number manufactured or sold by Fir-
eye shall be limited exclusively to the right to replacement or repair as above provided. In no event shall
Fireye be liable for consequential or special damages of any nature that may arise in connection with such
product or part.

FIREYE

CU-114

3 Manchester Road

MARCH 14, 2014

Derry, New Hampshire 03038 USA

Supersedes February 28, 2014

www.fireye.com

Summary of Contents for 85IRF series































Reviews: