FireplaceXtrordinair Elite Fireplacextrodin 36-Elite Owner'S Manual Download Page 21

 

Maintenance 

21 

©Travis Industries 

10/2/2019 - 1516 

36 Elite Owner’s 

Check Door Seal, Adjust if Necessary 

The door latch and door gasket work in conjunction to seal the firebox.  If the doors do not seal, air will 
leak into the firebox and cause the fire to burn too fast.  This reduces the ability to burn the fireplace 
overnight or precisely adjust the burn rate.  Follow the directions below to check the door gasket. 

 

Follow the directions below to check the door latch. 

 

Glass Inspection & Removal 

If the glass is cracked or broken, it must be replaced.  The glass & gasket should seal against the 
door.  See the illustration below for glass removal.  When re-installing the glass, gently press the rope 
gasket in place (use a putty knife). 

NOTE:

  This unit uses 5mm ceramic glass, use only OEM replacement glass. Do not use substitute 

materials. 

WARNING:

 

The top of the glass comes close to the face of the fireplace. The glass must be all the 
way down to prevent is from striking the fireplace when the door is closed. 

 

Check the door 
gasket.  It should 
adhere to the door 
and be intact 
(check both 
doors).  The 
gasket follows the 
perimter of the 
door along the 
outside edge (the 
inside edge does 
not have gasket).  

Use wood stove gasket 
cement to re-adhere 
loose gasket.

Severely frayed 
or thread-bare 
gasket should be 
replaced.

Latch

Inner 
Washer(s)

If the door latch rod does not keep 
the bottom of the doors snug 
against the firebox, bend the rod in 
slightly to create a tighter fit.

When closing the doors, the handle should pull the doors in and dreate a snug fit.  If it 
doesn’t check the following two items.

Door Handle

Outer 
Nut

Door Latch Adjustment

Doo
r

Door 
Latch 
Rod

If the door latch is 
loose, move one of 
the washers from the 
inner side of the 
latch shaft to the 
outer side.  For finer 
adjustments, tighten 
the outer nut against 
the inner nut to 
create a precise fit.

Inner Nut

Door Latch Rod Adjustment

Latch Shaft

Outer 
Washer(s)

9/16" Wrench

The rope gasket pins the glass in place.  
Remove it to access the glass.

The glass slides up 
and out of the door 
frame.

Cross-Section of 

Door & Glass

Glass

Door 

Frame

Channel 
Gasket

1/2” Dia. 
Rope Gasket

Summary of Contents for Elite Fireplacextrodin 36-Elite



























Reviews: