manualshive.com logo in svg

Firegear FGP-305, Installation And Operating Instructions Manual

Share
Download
Firegear FGP-305 Installation And Operating Instructions Manual Download Page 4

REV 8/21/06 Page 4 of 16

 

NOTE:

   If the above settings were not previously completed during 

the initial SET-UP and PROGRAMMING procedure, then the LCD 
screen will display SU, MORN, TIME and SET temperature digits.  
You must go back and perform the initial set-up procedure or the 
remote will not operate properly in the PROGRAM mode.  SEE 
PAGE 2. 
 

2 To 

program 

the DAY and PERIOD OF DAY, press the AHEAD or 

BACK buttons to display the DAY and PERIOD you wish to 
program. 

 

3 

When the DAY and PERIOD being programmed displays, then 
press the PROG button and the TIME will flash on the LCD screen. 

 

 
 

 

 

 
 
 

4 To 

program the START TIME, press the UP or DOWN button.  

Programmed start time settings are in 15-minute segments.  The 
new set time will display on the LCD screen. 

 

5 

When the desired START TIME displays press the PROG button 
and the SET TEMPERATURE will flash on the LCD screen. 

 

6 To 

program the SET TEMPERATURE, press the UP or DOWN 

button. 

 

7 

When the desired SET TEMPERATURE displays, then press the 
PROG button. 

 

8 

After pressing the PROG button in step 7, the next PERIOD of the 
same or next day will display on the LCD screen. 

 

9 To 

program the next PERIOD follow steps 3, 4, 5, 6 and 7. 

 

10  Continue to follow steps 3, 4, 5, 6 and 7 until all 7 days and the 4 

time periods in each day are programmed. 

 

11 Once 

ALL the programming has been completed, then press the 

SET button.  The programming data that has been entered will now 
over-ride the factory built-in program and operate your remote 
control system. 

 

PROGRAMMING NOTE:

 

 

Once in the programming process and you want to advance 
the programming procedure, you may bypass some of the 
DAYS or PERIODS OF DAY, by pushing the AHEAD or BACK 
buttons.  This allows you to eliminate the need to enter the 
TIME and TEMPERATURE for each DAY/PERIOD speeding 
up the programming process by skipping some of the ”software 
prompts”.  Once the LCD screen displays a DAY/PERIOD you 
want to reprogram, press the PROG button and follow the 
programming steps outlined above.   

 

 
 
 

 
 

TIME

SET

AM

START

     AT

PROGRAM

        FOR

SU

MORN

SET

AHEAD

BACK

PROG

1,3

2

 

TIME

SET

AM

START

     AT

PROGRAM

        FOR

SU

MORN

SET

AHEAD

BACK

PROG

4

5

TIME

SET

AM

START

     AT

PROGRAM

        FOR

SU

MORN

SET

AHEAD

BACK

PROG

6

7

TIME

SET

AM

START

     AT

PROGRAM

        FOR

SU

DAY

SET

AHEAD

BACK

PROG

11

 

Summary of Contents for FGP-305

















Reviews:

No comments

Brands by name

Popular brands

Load more brands