background image

Page 1 of 2

ICAF - 

Integrated Compressed Air Foam System

 

J

Limited Warranty

 

FM-0723-0-16D

Limited Warranty 

FireFlex Systems inc. (known herein as "the Manufacturer") 
warrants to its customer that its products shall be free of 
defects in material [or part(s)] and workmanship for a period 
of twelve (12) months from the date of original delivery, under 
normal use and service by the Customer (and provided that 
the product has been properly installed and maintained). 

The obligation of the Manufacturer in case of a claim made 
by the Customer hereunder, shall be, at the Manufacturer's 
option, limited to repair or replace, free of charge for parts or 
his labor, any product or part, which in the opinion of the 
Manufacturer, shall be proven to be defective.  The 
Manufacturer will NOT accept labor back-charges incurred by 
the Customer to repair or replace said product or part. 

The present warranty shall be void should the product [or 
part(s)] be altered by anyone other than the Manufacturer.  In 
case of a claim under the present warranty, the Customer 
must contact the Manufacturer's Customer Service 
Department as soon as he is aware of a claim and, subject to 
the authorization of the manufacturer, return the defective 
product [or part(s)], transportation prepaid, to the address 
listed below. 

This warranty constitutes the entire warranty given by the 
Manufacturer to the Customer with respect to the product. 
The present warranty is non-transferable and non-
assignable.  The Manufacturer does not represent that the 
products will prevent any loss by fire or otherwise or that the 
product will in all cases provide the protection for which it has 
been installed or intended. 

The Customer acknowledges that the Manufacturer is not an 
insurer.  The manufacturer shall not be liable for any loss or 
damages of any nature whatsoever, including but not limited 
to incidental or special or consequential damages including 
but not limited to, property damages, personal injury, revenue 
loss or lost profits, inconveniences, transportation charges or 
other damages suffered by anyone. 

There are no other warranties, expressed or implied with 
regard to the products, other than those contained herein. 

Some jurisdictions may not allow limitations on how long an 
expressed warranty lasts, so the above limitations may not 
apply to you.  Under no circumstances, shall the 
Manufacturer be liable for any loss of, or damage to property, 
direct or indirect, incidental or special or consequential 
damages, arising out of the use or inability to use the 
Manufacturer's products.  The Manufacturer shall not be 
liable for any personal injury which may arise in the course of 
or as a result of the use of the manufacturer's products. 

The Manufacturer shall not be liable for any personal injury 
which may arise in the course of or as a result of the use of 
the manufacturer's products. 

This warranty replaces all previous warranties and is the only 
warranty given by the Manufacturer with respect to its 
products.  This warranty shall not be modified, unless such 
modification is made in writing by an executive officer of the 
Manufacturer. 

In consideration of the warranty provisions contained herein, 
the Customer hereby waives the benefit of any statutory 
warranty or protection or remedy to which he may be entitled 
under the terms of any sales of goods act or similar 
legislation available to him in any jurisdiction in which the 
Customer carries on business. 

Defective part(s) must be returned to the address listed 
below within (30) days of receiving replacement parts(s).  If 
defective part(s) is not returned before delay expires, an 
invoice will be issued for replacement part(s) and shipping. 
On reception, an extended analysis will be performed on the 
said part(s).  If proven to be defective, no invoice will be 
issued.  If the part(s) is proven to be in working condition an 
invoice will be issued for replacement part(s) and shipping. 

Special Limitation:

 

 

Due to their self-discharge 

characteristics when not charged during extended storage 
periods, Batteries supplied with integrated Releasing Control 
Panels are covered by the above warranty for a period 
limited to three (3) months only. 

F

IRE

F

LEX

 Systems inc. 

1935, Lionel-Bertrand Blvd. 

Boisbriand, Quebec Canada 

J7

H

 1N8 

Tel.: (450) 437-3473 - Fax: (450) 437-1930 

Toll Free: (866) 347-3353 

Web site:  http://www.fireflex.com 

Summary of Contents for ICAF System










































Reviews:

Related manuals for ICAF System