manualshive.com logo in svg

Fire-Lite Alarms UDACT-F, Installation, Operation, And Programming Manual

Share
Download
Fire-Lite Alarms UDACT-F Installation, Operation, And Programming Manual Download Page 8

8

  Document # 50049  Rev D   5/2/97  P/N 50049:D

1.2

 Controls and

Indicators

Front Panel Switches
CLEAR

Digits 0-9

TEST

A

MODE

B

Up Arrow

C

Down Arrow

D

1st EVENT

E

ENTER/STORE

F

Displays
• EIA-485 - yellow LED
• COMM. FAIL - yellow LED
• KISS OFF - green LED
• POWER - green LED
• Four, Seven Segment Displays - red
• Primary Phone Line Active - red LED
• Secondary Phone Line Active - red LED
• TEST - green LED

The UDACT-F has been designed to be compatible with the following Fire-Lite
control panels:

• Sensiscan 2000
• MS-9200.

Two modular phone jacks allow easy connection to telephone lines. Modular jacks
are labeled PH1 and PH2 for the Primary and Secondary phone lines. Telephone line
'Primary and Secondary Active' red LEDs are provided as well as a green 'Kissoff'
LED.  The integral digital communicator provides the following functions:

• Line Seizure - takes control of the phone lines disconnecting any premises

phones.

• Off/On Hook - perform on and off-hook status to the phone lines.

• Listen for dial tone - 440 hertz tone typical in most networks.

• Dialing the Central Station(s) number - default is Touch-Tone®,

programmable to rotary.

• For tone burst or touchtone type formats: Discern proper 'Ack' and 'Kissoff'

tone(s) - The frequency and time duration of the tone(s) varies with the
transmission format. The UDACT-F will adjust accordingly.

• Communicate in the following formats (refer to Appendix for compatible

receivers:

✓

6 Tone Burst Types: 20 pps

       (3+1, 4+1, 4+2)

✓

 3 Touchtone Types:

       4 + 1 Ademco Express
       4 + 2 Ademco Express
       Ademco Contact ID

Figure 1-2: Controls and Indicators

1.3

     Compatible
             Panels

1.4

   Digital

          Communicator

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Summary of Contents for UDACT-F

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands