background image

15 

Picture no 8 

Side brush replacement 

The side brushes collect waste from the corners and carry it to the main brush. 
The rotation of the main brush is started by an hydraulic engine, while the its regulation is activated 
by a lever placed on the left side of the dashboard. 
The main brush ha sto be in contact to the floor with the front side and not the rear side. In order to 
replace  the  main  brush,  the  operator  has  to  unscrews  no.  4  screws  which  are  on  the  brush  hub. 
Afterwards,  the  operator  has  to  remove  the  old  main  brush  and  set  the  new  one  up.  Finally,  the 
operator has to tighten the 4 screws. 

Filter replacement 

Please follow the instructions below in order to replace the filter: 
1. Open the bonnet
2. Remove the filter shaker sheets
3. Replace the filters and their gaskets
Do now the opposite instructions.

Engine for filter shaker 

The engine for filter shaker makes the filters vibrate. In this way, the dust falls into the hopper. 
If the engine breaks down, the operator has to replace the carbon brushes. 

PROBLEMS AND DEFECTS 

DEFECT 

PROBABLE CAUSE 

SOLUTION 

The vehicle runs slowly 

A: the level of the hydraulic oil 
is not sufficient 
B:by-pass valve is open 
C: the pressure of the traslation 
circuiti is not sufficient 
D: the filter of the traslation 
circuiti is obstructed 

A: fill the hydraulic oil chamber 
B: close the valve  
C: check and regulate the 
pressure 

1.

Main brush

4. Hexagonal screws

Summary of Contents for S 48B






















Reviews: