Fike TWINFLEX SRM 100-0010 Installation Manual Download

Page: 2 / 18

26-1369-01

Contents

General Description ...................................................................................................... 3

Before Installation ......................................................................................................... 4

Positioning ...................................................................................................................................... 4

Device Installation / Mounting ...................................................................................................... 4

Connections .................................................................................................................. 6

Module Layout ................................................................................................................................ 6

Zone Connections (J1) ........................................................................................................ 7

Solenoid Connections (J2) .................................................................................................. 8

External Power for Solenoid (J3) ........................................................................................ 9

Input Connections (J4, J5, J6) .......................................................................................... 10

Discharge pressure circuit (J4) ......................................................................................... 11

Bottle pressure switch circuit (J5) ..................................................................................... 11

Solenoid Missing circuit (J6) ............................................................................................. 11

Acceptance Testing .................................................................................................... 12

Hardware Connections ............................................................................................... 13

Inspections & Testing ................................................................................................. 13

DIL Switch SW2 Settings ............................................................................................ 14

LED Table ..................................................................................................................... 15

Operation ..................................................................................................................... 16

Technical Data ............................................................................................................. 17

Technical Support ....................................................................................................... 18

Summary of Contents for TWINFLEX SRM 100-0010



















Search results

Summary of Contents for TWINFLEX SRM 100-0010

Reviews:

Related manuals for TWINFLEX SRM 100-0010

Brands by name

Popular brands

Fike TWINFLEX SRM 100-0010, Installation Manual

Search results

Summary of Contents for TWINFLEX SRM 100-0010

Reviews:

Related manuals for TWINFLEX SRM 100-0010

Brands by name

Popular brands