background image

 

PAGE / 8  

Doc. P/N 8.8128.00.3 

Rev. 3 / July, 2020 

 

 

Figure 6 - Pretorquaeble Holder (TQ+/TQ(+) Full Torque Configuration Shown) 

10.

 

Check  gap  between  base  and  hold down.  The gap  must  be the  same  size  on  all sides  of  the assembly.  This 
can  be assured  by measuring  the  distance  between  the  hold down and  base  at  various  places  around  the 
circumference  of the assembly.  Adjust  pre-assembly  screws  if necessary  to provide  an even gap (See  Figure 
7). 

 

 

Figure 7 - Gap Inspection 

11.

 

If holder  configuration  is TQ,  TQ+ or TQ(+) Full Torque,  torque  the  cap screws  to the values  shown  on the 
tag of the holder using crisscross  pattern in 20% increments  until the torque specified on the tag  is achieved 
on all cap screws. The torque values of the flange studs can be found on the tag of the rupture disc. 

CAUTION:  The  torque  value  on  the  tag  of  the  disc  and  the  tag  of  the  holder  may  vary.  Make  sure  to  use  the 
proper value. 

12.

 

If holder configuration is TQ, TQ+ or TQ(+) Full Torque, reconfirm the gap per step 10 after the cap screws are 
torqued. 

CAUTION: For TQ(+) Full Torque, depending on the flange execution do NOT use the torque value as shown on the 
nameplate of the bursting disc. The user must confirm the required load or torque value required when ordering. 

 

 

 

 

Summary of Contents for RD300 Holder



















Reviews: