background image

 
 
 

                

SUPPLEMENTARY OPERATING MANUAL 

 

 

 

 

 

02-11-05

 CDP-01 

Figure Sheet 1-811-B

 

 

 

COPYRIGHT 

 

 
 

 

NOTE 

 

These additional instructions explain the special features of the system delivered to the customer. They 
are intended for being used in conjunction with the CDP-01 Reference Manual. The CDP-01 Reference 
Manual applies except as noted to the contrary in these instructions. 
 
 

Copyright: 

 

All rights reserved. Any reproduction of this Additional Instruction Manual, in any form, in whole or in part, 
requires the prior written consent of FIFE. 
 
The information given in this Additional Instruction Manual is subject to change without notice. 
 
We have compiled this Additional Instruction Manual with the greatest possible care and attention: 
however, the possibility of error can not be completely excluded.  FIFE accepts no legal liability for 
incorrect information given and the consequences arising therefrom. 
 
 
Copyright 

 2002 FIFE Corporation, P.O. Box 26508, Oklahoma City, OK 73126,  U.S.A. 

 
                             FIFE GmbH,Postfach 1240, D-65762 Kelkheim/Ts.,  Germany 
 
 

Summary of Contents for CDP-01



















Reviews: