background image

FLSC  

GB 

Betriebsanleitung 

73734 Esslingen - Fiessler Elektronik  - Kastellstr.9 

• 

Doku Nr. 625    R.H. 

177

 

7. Diagnosis 

7.1 Diagnostic elements 

Three LEDs displaying the operation status of the FLSC are located on the top of the FLSC housing. 
The green and red LEDs are allocated to the safety output. 
The yellow LED signals – depending on the setting of the FLSC – an object in the warning field and/or 
dirt contamination of the front screen. In conjunction with the red LED, it also indicates whether the 
system is waiting for acknowledgement by the user. 
Should the device fail the self-test (system error), this is also displayed by the yellow LED. 

Diagnosis with FLSC LEDs: 

Status green 

yellow 

 

red 

Protective field clear 

 

Object in protective field 

 

Object in warning field 

 

Waiting for restart 

1Hz  

 

Dirt warning

 

1Hz

 

Dirt contamination * 

 

Self-test failed ** 

4Hz  

 

 

Dirt contamination of the FLSC front screen:  
see chapter 7.2 Maintenance! 

**  Self-test failed: see chapter 7.3 Service! 

 

The LEDs give the first diagnosis of the system status. Authorized personnel have, with the help of the 
user software supplied with the unit, access to an extensive diagnostic system (see chapter User 
Software in the FLSC technical description). 

7.2 Maintenance 

When set up appropriately by authorized personnel using the user software, the FLSC reports minor 
dirt contamination of the front screen with the dirt warning (when the device is functioning fully) as well 
as severe dirt contamination of the front screen (and shuts down the outputs at the same time). 
Clean the front screen if the device's dirt warning is activated. This is indicated by the slow flashing of 
the yellow LED while the green LED shines constantly (protective field clear). The front screen is an 
optical component and must not be scratched. Therefore clean it only with a soft cloth and plastic 
cleaner. (Recommended: Antistatic plastic cleaner, 1 litre,  
order no. 5 600 987) 
 
If the screen is scratched it must be replaced. The order number of the replacement front screen 
(including seals and screws) can be found in the chapter Accessories in the FLSC technical 
description. As the FLSC must be readjusted after replacement of the front screen, please advise your 
safety officer. 
 
Regularly check the tightness of all mounting screws on the FLSC and the fixing brackets. Also check 
all screws on the interface plugs. 
 
Regularly check that the device is functioning correctly by reaching into the protective field along its 
edges, corresponding to the appropriate application regulations. 

Summary of Contents for FLSC 101-312
































Reviews: