Mounting
Adjustment of the AKAS® at the first installation
23
6. Adjustment of the
AKAS®
at the first installation
adjustment of the receiver
adjustment of the transmitter
5
5.7
both supports must be mounted in a way that:
1. the highest (biggest) bending punch and the smallest
bending puch is within the range of the supports.
2. using the smallest bending punch, the receiver ele-
ment E2 + Z (
AKAS®-II
see fig. 19/2
)
, i..e. E1+Z
(
AKAS®-3
see fig. 19/1) are covered by the punch at
the highest range position of the support.
3. using the highest bending punch, the receiver element
E2 + Z (
AKAS®-II
see fig. 19/1
)
, i..e. E1+Z (
AKAS®-3
see fig. 19/1) can still be positioned correctly at the lo-
west position within the range of the suppoort.
Adjust the support with the help of a spirit level vertically,
i.e. parallel to the guiding rails of the ram.
Drop a perpendicular line from the bending line of the
bending punch and adjust optically the receiver with the
help of M6 adjustment screws so that the mark is
located vertically at the front of the receiver.
Check this over during the whole travel of the
support of the receiver by turning the key-opera-
ted switch to "EIN" (="ON") and carrying the recei-
ver upwards with pressing the button "EMPFÄN-
GER AUF"(="RECEIVER UP"). For doing this, the
adjustment mode must be in manual mode s.
chap. 5.8.). During the upward movement of the
receiver, repeatedly turn the key-operated switch to
"AUS" (="OUT") and check the distance between the
mark and the perpendicular (bending line) to make sure
that the receiver is carried up parallelly to the bending li-
ne. The displacement by the motor is not intended for
nonstop carrying up and down. In this case the thermal
protection switches off the motors. After letting go the
button and a short brake you may continue the carrying
procedure.
The transmitter must be mounted in a way that its marks
are located perpendicularly to the bending line, the same
way as the receiver is positioned. Adjustment must dbe
made just the way like the receiver.
The red transmitting beams should
meet the receiver like it is shown in the
opposite illustration. When doing so,
please observe that the receiver stays
in the lower stop of the support. To
check this, cover the transmitter entire-
ly. Then the receiver should not move
further downwards. The adjustment
mode must be in manual mode (s.
chap.5.8.)
To guarantee a trouble-free operation, the mecanical fix-
tions of both the receiver and the transmitter must be fi-
xed at solid, deformation-free plane-parallel construc-
tions at the ram.
The fastening brackets are designed for the fastening
and adjustment of the AKAS®-LC.
Together with the sliding tenein blocks, the brackets al-
low a universal fastening.
Transmitter and receiver must be mounted in a way that
the receiver element E4 remains free when the bending
punch is fixed .
If a height-adjustable support is used, adjust the sup-
port with the help of a spirit level vertically, i.e. parallel to
the guiding rails of the ram.
Drop a perpendicular from the bending line of the ben-
ding punch and adjust optically the receiver with
the the help of M4 adjustment screws so that the
mark (centre of the receiver elements) is located
vertically at the front of the receiver. When using
a manually movable support for transmitter and
receiver, make this test along the entire displa-
cement area.
Check the distance between the mark and the
perpendicular (bending line) to make sure that
the receiver is carried up parallelly to the bending line.
The transmitter must be mounted in a way that its marks
are located perpendicularly to the bending line, the sa-
me way as the receiver is positioned.
If a support is used, adjust the support with the help of
a spirit level vertically, i.e. parallel to
the guiding rails of the ram.
The red transmitting beams should
meet the receiver like it is shown in-
the opposite illustration.
Transmitter and receiver must be mounted at the same
height if both are installed in the lowest position of the
supports.
Sendestrahlen
AKAS®-LC Fig. 23/5
Fig. 23/ 2
Lot
The receiver and the transmitter must be swiveled around the longitudinal axis in a way that their housings are pla-
ne parallel to the ram. With pivoting around the longitudinal axis, the adjustment screw or the locknut that counte-
racts the screwing movements, must be loosened.
Ram
receiver housing
Fig. 23/1
Sendestrah-
AKAS®-II Fig. 23/4
Doku Nr. 988 Stand 3.2.2016 / Aui
transmitter beams
AKAS®-3 Fig. 23/3
transmitter beams
transmitter beams
-AKAS®-3... / AKAS®-II...
-AKAS®-LC...
FIESSLER
E L E K T R O N I K
