manualshive.com logo in svg

Festo CRDNG Series, Repair Instructions, Page: 25 / 26

Share
Download
Festo CRDNG Series Repair Instructions Download Page 25

25 / 26

Festo 7CRDNGb_en

7 

Tools

This chapter provides an overview of the tools and accessories required to repair the cylinder with piston rod.

7.1 

Standard tools

The following standard tools among others are required to repair the cylinder with piston rod:

• 

Screwdriver

• 

Wrench

• 

Flat pliers

• 

Torque wrench (see tables in the corresponding repair steps for values)

7.2 

 Special  tools

The following special tools are required to repair and service the cylinder with piston rod:

Designation

Additional information

Illustration

Mounting sleeve for piston rod

The mounting sleeve for piston rods for 
protecting the piston rod seal and the bearing 
in the bearing cap while the repair is 
being carried out must be produced by 
the customer.
The schematic diagram can be found in 
the information brochure 

"Accessories, 

equipment and tools"

 (7Accessories_a_en).

Documents

Further information on the special tools and schematic diagrams can be found in the information brochure 

"Accessories, equipment and tools"

 (7Accessories_a_en). It can be found in the online spare parts catalogue on 

the Festo website (

http://spareparts.festo.com/xdki/data/SPC/0/PDF_SAFE/Hilfsmittel.pdf

).

8 

 Liability

The General Terms and Conditions of Sale of Festo AG & Co. KG, which can be viewed on the Festo website 
(

www.Festo.com

), apply.

Summary of Contents for CRDNG Series



























Reviews:

No comments