manualshive.com logo in svg

Festo CRDNG Series, Repair Instructions, Page: 15 / 26

Share
Download
Festo CRDNG Series Repair Instructions Download Page 15

15 / 26

Festo 7CRDNGb_en

• 

Clean the seat of the piston rod seal 

1

.

• 

Clean the seat of the O-ring 

2

.

• 

Clean the seat of the cushioning seal 

3

.

See chapter 

5.1 "Cleaning"

1

2

3

• 

Only with CRDNG-125-…-PPV-A-S2

–  Clean the seat of the piston rod seal 

1

.

–  Clean the seat of the O-ring 

2

.

–  Clean the seat of the cushioning seal and sleeve 

3

.

See chapter 

5.1 "Cleaning"

 

1

2

3

• 

Grease the new piston rod seal (one per bearing cap on cylinders with 
through piston rod (S2 )) as follows:

Area

Greasing

1

 Grease reservoir

1)

 for piston rod

Fill 2/3 with grease

2

 External surface for bearing cap

Thin fi lm

2)

3

 Grease reservoir

1)

 for bearing

Fill 2/3 with grease

1)

  See chapter 

5.2.3 "Grease reservoir" 

2)

  See chapter 

5.2.2 "Thin grease fi lm"

1 2 3

• 

Insert the piston rod seal into the bearing cap (in both bearing caps on 
cylinders with through piston rod (S2)) using an appropriate thrust piece.

Note

Note the mounting direction (individual sealing lips facing out).

• 

Grease the new O-rings and insert them into the grooves in the bearing 
cap and end cap (the rear bearing cap on cylinders with through piston rod 
(S2 )).

•  Apply a thin fi lm of grease to the new cushioning seals on the front side 

of the sealing surface and insert them into the bearing cap and end cap 
(the rear bearing cap on cylinders with through piston rod (S2 )).

Summary of Contents for CRDNG Series



























Reviews:

No comments