Ferrofish PULSE16 DX User Manual Download Page 25

Page: 25 / 28

CE conformity

EMC

This device fully complies to all harmonised standards for the

approximation of laws of the member states for the electromechanical

compatibility

(EMC:2014/30/EU) and European Low Voltage Directive 2014/35/EU.

RoHs

This device has been produced with lead free solder according to the

EU directive 2011/65/EU and therein contained maximum permissible

values for hazardous substances found in electronic devices.

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any interference

received, including interference that may cause undesired operation.

Responsible Party in USA:

Synthax United States, 6600 NW 16th

Street, Suite 10, Ft Lauderdale, FL 33313 T.:754.206.4220

Trade Name: Ferrofish, Model Number: PULSE16 / PULSE16 DX MX

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Summary of Contents for PULSE16 DX





























Search results

Summary of Contents for PULSE16 DX

Reviews:

Related manuals for PULSE16 DX

Brands by name

Popular brands

Ferrofish PULSE16 DX, User Manual

Search results

Summary of Contents for PULSE16 DX

Reviews:

Related manuals for PULSE16 DX

Brands by name

Popular brands