Not for
Reproduction
45
Problem: Engine runs but mower will not drive.
Transmission drive belt is slipping.
See problem and cause below.
Brake is not fully released.
See authorized service dealer.
Problem: Transmission drive belt slips.
Cause
Remedy
Pulleys or belt is greasy or oily.
Clean as required.
Tension is too loose.
Adjust spring tension. See
"Transmission Drive Belt
Replacement".
Belt stretched or worn.
Replace belt.
Problem: Parking brake will not hold.
Cause
Remedy
Brake is incorrectly adjusted.
See "Parking Brake Adjustment".
Problem: Mower steers or handles poorly.
Cause
Remedy
Ground speed control lever linkages
are loose.
Check and tighten any loose
connections.
Improper tire inflation.
See "Specifications" for proper tire
inflation and adjust tire pressures
accordingly.
Tracking needs adjustment.
See "Tracking Adjustment".
Troubleshooting the Mower Deck
Problem: Mower deck will not raise.
Cause
Remedy
Lift Linkage not properly attached or
damaged.
See authorized service dealer for
repair.
Problem: Engine stalls easily with mower deck engaged.
Cause
Remedy
Engine speed too slow.
Set to full throttle.
Ground speed to fast.
Decrease ground speed.
Cutting height set too low.
Cut tall grass at maximum cutting
height during first pass, and then
at the desired cutting height for the
second pass.
Discharge chute jamming with cut
grass.
Cut grass with discharge pointing
towards previously cut area.
Problem: Excessive mower deck vibration.
Cause
Remedy
Blade mounting bolts are loose.
Tighten to 120 ft. lbs. (163 N.m.).
Mower blades, arbors, or pulleys are
bent.
Check and replace as necessary.
Mower blades are out of balance.
Remove, sharpen, and balance
blades. See "Servicing the Mower
Blades".
Belt installed incorrectly.
Reinstall the belt correctly.
See "Mower Deck Drive Belt
Replacement".
Problem: Excessive belt wear or breakage.
Cause
Remedy
Bent or rough pulleys.
Repair or replace.
Using incorrect belt.
Replace with correct belt.
Problem: Mower deck drive belt slips or fails to drive.
Cause
Remedy
Idler pulley spring broken or not
properly attached.
Repair or replace as needed.
Mower deck drive belt is broken.
Replace mower deck drive belt.
Problem: Mower (blades) does not engage.
Cause
Remedy
Electrical wiring damage.
Locate and repair damaged wire.
Operator is not standing on the
operator platform.
Operator stands on the operator
platform and pulls up on the PTO
(Power Take Off) switch.
Troubleshooting Common Cutting
Problems
Problem: Streaking
Streaking is when thin strips of uncut grass are left behind the mower.
Streaking is usually caused by operator error or poor blade maintenance.
Cause
Remedy
Blades are not sharp.
Sharpen your blades.
Blades are worn down too far.
Replace your blades.
Engine speed is too slow.
Always mow at full throttle.
Ground speed is too fast.
Slow down.
Deck is plugged with grass.
Clean out the mower.
Not overlapping cutting rows enough. Overlap your cutting rows
Not overlapping enough when
turning.
When turning your effective cutting
width decreases–overlap more when
turning.
Problem: Scalping
Scalping is when the mower deck comes close to or hits the ground.
Scalping can be caused by the mower deck misadjustment, unevenness in
the lawn, or by mower deck bouncing because the ground speed is too fast.
Cause
Remedy
Lawn is uneven or bumpy.
Roll or level the lawn.
Mower deck cutting height is set too
low.
Raise the cutting height.
Ground speed is too fast.
Slow down.
Deck is not leveled correctly.
Correctly level the deck.
Tire pressure is low or uneven.
Check and inflate the tires.
Problem: Stepped Cutting
Stepped cutting is sharp ridges or uneven levels left in the lawn
surface. Stepped cutting is usually caused by mower deck damage or
misadjustment, or damage to the mower blades.