manualshive.com logo in svg

Ferno 175 Series, Technical Service Bulletin, Page: 7 / 13

Share
Download
Ferno 175 Series Technical Service Bulletin Download Page 7

Ferno Technical Service Bulletin

© Ferno-Washington, Inc. / 234-3601-00

7

Antler to Rail Measurement

Series

C 

Distance 

(Antler to Rail)

25, 26

46.187” 

1173 mm

35X-EFNY

46.886" 

1191 mm

35A, 35A+ 

52.187” 

1326 mm

PROFlexx 35P, 35X

51.529” 

1309 mm

POWERFlexx

51.529” 

1309 mm

93ES, 93EX

52.439” 

1332 mm

PROFlexx 93P, 93H

52.439” 

1332 mm

All measur/- .125” (3 mm)

12 

Measurement

5.  Inspect for Proper Placement 

 

of the Antler and Rail

ANTLER TO RAIL LENGTH MEASUREMENT

Are the antler and rail the proper front-to-back distance from one 

another? Does the cot fit properly in the fastening system? Refer to the 

measurement in the table at right, Figure 12, and the instructions below.

1.  Using a pencil and ruler or straight edge, mark a line perpendicular 

to the rail release button on the floor.

2.  Using a pencil and ruler or straight edge, mark a line from the 

inside of the antler hook to meet the line you made in Step 2.

3.  Verify the antler and rail are the proper distance apart and the cot 

fits properly into both fastening-system components.

ANTLER TO RAIL CENTERLINE MEASUREMENT

Are the antler and rail the proper side-to-side distance from one 

another? Refer to Figure 13 and the instructions below.

1.  Using a pencil and measuring tape, mark a line from the center of 

both 

antler mounting blocks to the rail.

2.  Using a pencil and measuring tape, mark a line perpendicular to 

the line you made in Step 1 to the center of the rail bracket.

3.  Verify the antler and rail are the proper distance apart.

 

○

A wall-mounted rail should be 13” (330 mm) from the antler 

centerline.

 

○

A floor-mounted rail should be 14-1/2” (368 mm) from the antler 

centerline.

13 

Measurement

Summary of Contents for 175 Series














Reviews:

No comments