manualshive.com logo in svg

Ferno 175 Series, Technical Service Bulletin, Page: 12 / 13

Share
Download
Ferno 175 Series Technical Service Bulletin Download Page 12

© Ferno-Washington, Inc. / 234-3601-00

Ferno Technical Service Bulletin

12

Limited Warranty Statement

The products sold by Ferno are covered by a limited warranty, which 

is printed on all Ferno invoices. The complete terms and conditions of 

the limited warranty, and the limitations of liability and disclaimers, 

are also available upon request by calling Ferno at 1.800.733.3766 or 

1.937.382.1451.

Repairs or Parts

EMSAR

®

 is the only organization authorized by Ferno 

to manage, service, and repair Ferno products.

Telephone (Toll-free) 

1.800.73.EMSAR

Telephone (Worldwide) 

1.937.383.1052

Fax (Worldwide) 

1.937.383.1051

Internet 

www.EMSAR.com

Ferno Customer Relations

For ordering assistance or general information:

CANADA AND THE U.S.A.

Telephone (Toll-free) 

1.877.733.0911

Telephone  

1.937.382.1451

Fax (Toll-free) 

1.888.388.1349

Fax 1.937.382.1191

Internet 

www.ferno.com

ALL OTHER LOCATIONS

For assistance or information, please contact your Ferno distributor. If 

you do not have a Ferno distributor, please contact Ferno Customer 

Relations:

Ferno-Washington, Inc., 70 Weil Way 

Wilmington, Ohio 45177-9371, U.S.A.

Telephone  

+1.937.382.1451

Fax +1.937.382.6569

Internet 

www.ferno.com

Parts

Model 175-

Description

Kit 

Number

Qty.

1 2 3 4 5

•

•

•

•

•

Ferno J-Safety Hook

082-2019

1

•

•

•

•

•

Ferno 2.5”/64 mm Safety Hook

090-5015

1

•

•

•

•

•

Ferno 4”102 mm Safety Hook

090-1308

1

•

•

•

•

•

Standard Antler (only)

090-0271

1

•

•

•

•

•

iN∫X Antler (only)

056-7052

1

•

•

•

Antler Mounting Block (Removable)

090-0264

1

•

•

Antler Mounting Block (Permanent)

090-0272

2

•

•

•

Floor Plate for Removable Antler

090-0265

2

•

•

Floor Plate for Removable Mounting Bracket

090-0266

1

•

•

•

Removable Tie-Down Knob, Short (for Bracket or Antler)

090-0268

1

•

•

•

•

•

Replacement Split Fastener Post (25, 26, 29-M, 35A/35A+, 93ES/93EX)

090-0277

1

•

•

•

•

•

Replacement Split Fastener Post (35P, 35X PROFlexx, POWERFlexx)

190-1240

1

•

•

•

•

•

Replacement Split Fastener Post (93P, 93H PROFlexx)

190-1154

1

•

•

•

•

•

Replacement Split Fastener Post (original side-mount POWERFlexx)

190-1469

1

•

•

•

•

•

Label Kit (Set)

090-4229

1

•

•

Removable Floor Mounting Bracket (10-Hole)

090-0263

1

•

Permanent Floor Mounting Bracket (10-Hole)

190-1400

1

•

•

Wall Mounting Bracket

190-1398

1

•

•

Rail Clamp for Wall Bracket w/hardware (New wide clamp, 4-hole)

190-1451

1

•

•

•

Rail Clamp for Floor Bracket w/hardware (New wide clamp, 4-hole)

190-1399

1

•

•

•

•

•

Rail, Aluminum (Standard)

090-0278

1

•

•

•

•

•

Rail, Stainless Steel

090-5692

1

•

•

•

•

•

Rail Push Handle

090-4226

1

•

•

•

•

•

Rail Spring and Bushing

090-4227

1

•

•

1.5" SHCS and Nut (Coverts Permanent Floor Rail Bracket to Removable)

090-5048

1

•

•

Mounting Plate Plastic Cover Kit (set: 2 antler, 1 rail)

081-9734

1

•

•

•

Modified Antler Mounting Block for Series 35 and Series 30 in-line

081-9912

1

•

•

•

•

•

Rail Clamp Hardware (Set: Wall or Floor)

190-2091

1

Summary of Contents for 175 Series














Reviews:

No comments