background image

GENERAL INFORMATION

Operator's Manual Combines  FENDT 5275 C-6335 C- EN - LA327317011 - 09/2011

1-21

Special remarks for 5275 C PL and 6335 

C PL models under levelling system use 

conditions

1.) Note the working conditions for C 

PL

combines on firm ground when levelling is 

activated:

• Crosswise  . . . . . . . . . . . . . . . . . . . .  20%

• Lengthwise  . . . . . . . . . . . . . . . . . . . .  0%

2.) Pay attention to the slope and the type of 

ground, as this could reduce the machine grip. 

On rough ground, drive carefully and reduce 

speed.

3.)

When using cross levelling, never exceed 

the allowable limit, which is indicated by the 

buzzer and a specific message on the 

display.

Only work if the machine body is horizontal; 

it is extremely dangerous to drive when the 

machine is inclined to one side

.

4.) When working on slopes, do not exceed the 

working limit, which is indicated by the buzzer 

and a specific message on the display.

If the machine tends to lift at the rear, whatever 

the situation, lower the cutting table 

completely.

5.) Preferably work in crosswise passes; 

when 

changing direction, always point the cutting 

table uphill.

6.) Make no sudden turns, especially when the 

grain tank is full: 

Note that the levelling 

system has a technical response time

.

7.) When driving downhill, never exceed 5-6 km/h.

8.) Couple the brake pedals to prevent braking 

errors.

Keep the braking system perfectly efficient. 
Check the oil level in the tank frequently and 
replace the friction pads before they are 
completely worn. 

9.) Change gears on flat ground or where there is 

only a slight gradient. Proceed as follows:

• Make sure that four-wheel drive is engaged

• Move the multifunction lever to the neutral 

position

• Lower the cutting table

• Press the service brakes and change gear

• Do not use fourth gear for work in the field.

10.)

Overconfidence in the use of the combine 
can result in a lack of attention and can 
therefore create dangerous situations

.

11.)

Frequently check the efficiency of the 
manual levelling systems, as they must 
provide additional safety in case the 
automatic levelling feature fails: Note that 
the manual systems override the automatic 
systems, although they are not normally in 
operation

.

12.) Never operate the machine, not even for a 

short time, when it is manually inclined on flat 
ground, as the engine lubrication may be 
inadequate. 

13.) Check tyre pressure: Insufficient pressure 

endangers tyre integrity, with potentially 
serious consequences. 

14.) Use the appropriate switch before road 

transport.

Summary of Contents for 5275 C
































Reviews: