background image

About This Manual 

The manual mainly describes the product information, guidelines for installation, operation and 

maintenance. The manual cannot include complete information about the photovoltaic (PV) 

system.

How to Use This Manual 

Read the manual and other related documents before performing any operation on the inverter. 

Documents must be stored carefully and be available at all times. 

Contents may be periodically updated or revised due to product development. The information in 

this manual is subject to change without notice. The latest manual can be acquired via our 

website at 

http://www.felicitysolar.com

 for latest version.

Safety Introductions

This chapter contains important safety and operating instructions. Read and keep this manual 

forfuturereference.

·

 Before using the inverter, please read the instructions and warning signs of the battery 

  and corresponding sections in the instruction manual. 

·

 Do not disassemble the inverter. If you need maintenance or repair, take it to a 

  professional service center. 

·

 Improper reassembly may result in electric shock or fire. 

·

 To reduce risk of electric shock, disconnect all wires before attempting any maintenance 

  or cleaning. Turning off the unit will not reduce this risk. 

·

 Caution: Only qualified personnel can install this device with battery. 

·

 Never charge a frozen battery. 

·

 For optimum operation of this inverter, please follow required specifification to select 

  appropriate cable size. It is very important to correctly operate this inverter. 

·

 Be very cautious when working with metal tools on or around batteries. Dropping a tool 

  may cause a spark or short circuit in batteries or other electrical parts, even cause an 

  explosion. 

·

 Please strictly follow installation procedure when you want to disconnect AC or DC 

   terminals. Please refer to "Installation" section of this manual for the details. 

·

 Grounding instructions - this inverter should be connected to a permanent grounded  

   wiring system. Be sure to comply with local requirements and regulation to install this 

   inverter. 

·

 Never cause AC output and DC input short circuited. Do not connect to the mains when 

  DC input short circuits.

Hybrid solar inverter   

Hybrid solar inverter  

1. SAFETY & WARNING

This manual provides relevant information with icons to highlight the physical and property safety 

of the user to avoid device damage and physical injury. 

The Symbols used in this manual are listed as below: 

Symbols

Name

Instruction

Danger

Warning

Electrostatic  sensitive

Hot surface

Earth terminal

Note

CE mark

EU WEEE mark

Serious physical injury or even death may occur 
if not follow the relative requirements

Physical injury or damage to the devices may 
occur if not follow the relative requirements

Damage may occur if not follow the relative 
requirements

Sides of the device may become hot. 
Do not touch.

The inverter must be reliably grounded.

Ensure that DC and AC side circuit breakers have
been disconnected and wait at least 5 minutes 
before wiring and checking.

The procedures taken for ensuring proper operation.

The inverter complies with the CE directive.

Product should not be disposed as household waste.

2.Product Introduction

Felicity Solar IVGM4648/5048 is a multifunctional inverter, combining functions of inverter, solar 

charger and battery charger to offer uninterruptible power support with portable size. Its 

comprehensive LCD display offers user configurable and easy accessible button operation such as 

battery charging, AC/solar charging, and acceptable input voltage based on different applications. 

NOTE

01

02

Caution

Summary of Contents for IVGM4648


















Reviews: