22
WSG 8-115 / WSG 13-125 / WSG 9-125 / WSG 13-125 S
WSG 13-150 / WSG 9-70 E / WSG 13-70 E
EN
Mounting the guard WSG 9-125/WSG 13-125 S/
WSG 13-150/WSG 9-70 E/WSG 13-70 E
(Figure 8).
➤
Loosen the tightening screw (8b).
➤
Insert the clip of the wheel guard (8)
into the groove on the power tool.
➤
Turn the wheel guard (8) to the
required working position and clamp the
wheel guard (8) using the tightening
screw (8b).
Adjustments.
Adjusting the guard WSG 8-115/WSG 13-125
(Figure 7).
➤
Press the locking button (7a) upwards
and keep it pressed.
➤
Swivel the guard (7) into the required
working position.
➤
Let go of the locking button (7a) and
engage the guard (7).
Adjusting the guard WSG 9-125/WSG 13-125 S/
WSG 13-150/WSG 9-70 E/WSG 13-70 E (Figure 8).
➤
Loosen the tightening screw (8b).
➤
Turn the wheel guard (8) to the
required working position and clamp the
wheel guard (8) using the tightening
screw (8b).
Changing the tool.
Attaching or changing the wheel (Figure 5).
Only press the locking button (1) when
the motor is not running.
➤
Press the locking button (1) and keep it
pressed down. Undo the threaded flange
using the face spanner.
➤
Completely unscrew the threaded
flange (5).
➤
Change the used accessory or insert a
new one.
In so doing, make sure that the grinding
tool is centred properly between the inner
and threaded flange.
➤
Screw the threaded flange (5) in again by
hand.
➤
Press the locking button (1) and keep it
pressed down. Screw the threaded flange
tightly using the face spanner.
Securing the work piece.
➤
Secure the workpiece adequately.
A
workpiece that is not properly secured
can, for example, cause the accessory to jam and
kick back, fall and cause other hazards.
General operating instructions.
Putting into operation.
First check that the mains supply lead and
mains plug are not damaged.
Starting (Figure 10).
After inserting the mains plug, the angle grinder
can be started in any working position by press-
ing the pressing surfaces (4) twice in succession.
➤
Hold the angle grinder in the required
working position, either at the
back (START A) or front (START B); lightly
press at least one of the 4 pressing surfaces, and
keep it/them pressed.
Please note:
The accessory begins to move with
short, low-power impulses. The angle grinder
thereby indicates that the first pressing surface
has been activated.
For the working position holding the power tool
at the back (START A):
➤
Briefly
press the pressing surface near
the auxiliary handle with your thumb.
For the working position holding the power tool
at the front (START B):
➤
Briefly
press one of the buttons at the back.
The angle grinder starts gently and reaches
its working speed after a short time.
Please note:
The angle grinder does not start up:
– if the pressing surfaces (4) are pressed at the
front
and
the back at the same time
– if one or more of the pressing surfaces is/are
pressed while the mains plug is inserted
Setting the speed WSG 9-70 E/WSG 13-70 E
(Figures 2+3).
The speed can be set to different levels.
To increase the speed:
➤
Briefly press button (2).
Reducing the speed:
➤
Keep button (2) pressed down.
➊
➋
➋
3 41 01 050 06 0.book Seite 22 Dienstag, 12. Juni 2007 10:57 10
