background image

 

Installation 

cVEND plug 

 

FEIG ELECTRONIC GmbH 

Page 4 of 24 

cVEND

 plug - User manual.docx

 

 

1. Warnings - Read before start-up ! 

1.1. Safety Instructions 

 

The  device  may  only  be  used  for  the  intended  purpose  designed  for  by  the 
manufacturer. 

 

The operation manual should be conveniently kept available at all times for each user. 

 

Unauthorized changes and the use of spare parts and additional devices which have not 
been  sold  or  recommended  by  the  manufacturer  may  cause  fire,  electric  shocks  or 
injuries. Such unauthorized measures shall  exclude any liability by the manufacturer. 

 

The liability-prescriptions of the manufacturer in the issue valid at the time of purchase 
are  valid  for  the  device.  The  manufacturer  shall    not  be  held  legally  responsible  for 
inaccuracies,  errors,  or  omissions  in  the  manual  or  automatically  set  parameters  for  a 
device or  for an incorrect application of a device. 

 

Repairs may only be executed by the manufacturer. 

 

Installation,  operation,  and  maintenance  procedures  should  only  be  carried  out  by 
qualified personnel. 

 

Use  of  the  device  and  its  installation  must  be  in  accordance  with  national  legal 
requirements and local electrical codes . 

 

When working on devices the valid safety regulations must be observed. 

 

Special advice for carriers of cardiac pacemakers: 

Although  this  device  doesn't  exceed  the  valid  limits  for  electromagnetic  fields  you 
should  keep  a  minimum  distance  of  25  cm  between  the  device  and  your  cardiac  pace-
maker and not stay in  an immediate proximity of the device respective the antenna for 
some time.  

 

1.2. Security Instructions 

 

DO  NOT  DISASSEMBLE  ANY  PART!  The  device  contains  a  battery-powered  security 
circuited.  The  security  circuit  will  be  triggered  if  security  relevant  parts  are 
disassembled. In such cases the device stops regular operation and can be reactivated 
only by the manufacturer in a certified secure environment. 

 

 

Summary of Contents for cVEND plug

























Reviews: