background image

 

Installation 

cVEND plug 

 

FEIG ELECTRONIC GmbH 

Page 2 of 24 

cVEND

 plug - User manual.docx

 

 

Note 

 Copyright 2014 by 

FEIG ELECTRONIC GmbH 
Lange Strasse 4 
D-35781 Weilburg 
Tel.: +49 6471 3109-0 

http://www.feig.de

 

With the edition of this document, all previous editions become void. Indications made in this manual may be 

changed without previous notice. 

The reproduction, distribution and utilization of this document as well as the communication of its contents to 

others without express authorization is prohibited. Offenders will be held liable for the payment of damages. 

All rights reserved in the event of the grant of a patent, utility model or design. 

Composition  of  the  information  in  this  document  has  been  done  to  the  best  of  our  knowledge.  FEIG 

ELECTRONIC  GmbH  does  not  guarantee  the  correctness  and  completeness  of  the  details  given  in  this 

manual  and  may  not  be  held  liable  for  damages  ensuing  from  incorrect  or  incomplete  information.  Since, 

despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips. 

The instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC 

GmbH  does  not  give  any  guarantee  promise  for  perfect  function  in  cross  environments  and  does  not  give 

any guaranty for the functionality of the complete system which incorporates the subject of this document. 

FEIG ELECTRONIC call explicit attention that devices which are subject of this document are not designed 

with components and testing methods for a level of reliability suitable for use in or in connection with surgical 

implants  or  as  critical  components  in  any  life  support  systems  whose  failure  to  perform  can  reasonably  be 

expected  to  cause  significant  injury  to a  human.  To avoid  damage, injury,  or  death,  the  user  or  application 

designer must take reasonably prudent steps to protect against system failures. 

FEIG  ELECTRONIC  GmbH  assumes  no  responsibility  for  the  use  of  any  information  contained  in  this 

document  and  makes  no  representation  that  they  free  of  patent  infringement.  FEIG  ELECTRONIC  GmbH 

does not convey any license under its patent rights nor the rights of others. 

 

All brand names, trademarks or logos are property of their respective owners. 

 

 

 

Contact: 

Commercial Questions:  [email protected] 
Technical Questions: 

[email protected] 

Summary of Contents for cVEND plug

























Reviews: