background image

 

 

 

  The user must respect the requirements and precautions in the case of resupply by generating sets 

of  an  installation,  depending  on  existing  protective  measures  in  this  installation  and  applicable 

regulations. 

  Generating sets should only be loaded up to their rated power under the rated ambient conditions.  

 

Prior to commencing maintenance work it shall be ensured that untimely start-up is not possible.

 

 

1.3 SECURITY MEASURES WHEN FILLING THE FUEL TANK 

  The fuel is extremely flammable and poisonous. 

  This generator only uses petrol (gasoline); any other kind of fuel will damage the motor. 

  Do  not  overfill  the  tank  with  petrol  to  avoid  spilling.  If  you  notice  a  spill,  it  must  be  wiped  up 

completely with a dry cloth before starting the motor. 

  If you swallow fuel by mistake, if you inhale fuel vapors or if you get drops of fuel in your eyes, see a 

doctor immediately. If a certain quantity of fuel is spilt on your skin or clothing, wash or change your 

clothes. 

  Always stop the motor of the generator when filling it with fuel.  

  Never fill the fuel tank while smoking or near a naked flame. 

 

Make sure you don’t spill fuel on the motor and the exhaust grille of the generator during filling with 

fuel. 

  Keep the fuel in an appropriate recipient and sheltered from any sources of fire. 

  Carry out filling in a safe place, and slowly open the fuel cap to release the pressure which has built 

up inside the tank. Wipe up any drops of petrol that have spilled before starting the motor. 

  To prevent fire, move the generator at least 4 meters away from the area for filling with fuel. 

  Make sure that the fuel cap is tightly closed before starting. 

  Do not keep petrol in the tank for a long time. 

            While  using  or  transporting  the  generator,  make  sure  you  keep  the  generator  upright, 

otherwise the fuel may escape from the carburetor or the fuel tank. 

 

1.4 ELECTRICAL SAFETY  

  Before  each  use  ensure  that  the  load  to  be  connected  does  not  exceed  the  power  of  the  current 

produced by the generator. 

To avoid electric shock, you must follow the following instructions: 

  Do not touch the generator with wet hands. 

  Do not run the generator under rain or snow. 

  Do not run the generator near water. 

  Connect the generator to earth. Use a sufficiently thick conductor for the earth wire. 

  Do not operate the generator in parallel with another generator. 

  If using electrical extensions, make sure that they are sufficiently thick to transport the current and 

that they are used correctly. 

 

The  connection  of  a  generator  used  for  auxiliary  power  to  the  electrical  installation  of  a 

building  must  be  performed  by  a  qualified  electrician,  and  in  conformity  to  the  provisions  of  the 

Summary of Contents for FG3000-A

































Reviews: