background image

WARRANTY

The  manufacturer  guarantees  the  product  against  defects  in  material  and  workmanship  for  a  period  of  2 
years from the date of the original purchase. The warranty only applies if the product is for household use. 
The warranty does not cover breakdowns due to normal wear and tear.

The  manufacturer  agrees  to  replace  parts  identifed  as  defective  by  the  designated  distributor.      The 
manufacturer does not accept responsibility for the replacement of the machine, in whole or in part , and/or 
ensuing damage.

The warranty does not cover breakdowns due to:

• insufcient maintenance.

• abnormal assembly, adjustment or operations of the product.

• parts subject to normal wear and tear.

The warranty does not extend to:

• shipping and packaging costs.

• using the tool for a purpose other than that for which it was designed.

• the use and maintenance of the machine done in a manner not described in the user manual.

Due to our policy of continuous product improvement, we reserve the right to alter or change specifcations 
without  notice.  Consequently,  the  product  may  be  diferent  from  the  information  contained  therein,  but  a 
modifcation  will  be  undertaken  without  notice  if  it  is  recognized  as  an  improvement  of  the  preceding 
characteristic.

READ THE MANUAL CAREFULLY BEFORE USING THE MACHINE.

When ordering spare parts, please indicate the part number or code, you can fnd this in the spare parts list 
in this manual. Keep the purchase receipt; without it, the warranty is invalid. To help you with your product, 
we invite you to contact us by phone or via our website:

• 

+33 (0)9.70.75.30.30

• 

https://services.swap-europe.com/contact

You must create a "ticket" via the web platform.

• Register or create your account.

• Indicate the reference of the tool.

• Choose the subject of your request.

• Describe your problem.

• Attach these fles: invoice or sales receipt, photo 

of the identifcation plate (serial number), photo 
of  the  part  you  need  (for  example:  pins  on  the 
transformer plug which are broken).

8

. WARRANTY

22

Summary of Contents for FELPRO25-AC


























Reviews: