background image

5

CX SERIES Installation, Operating & Maintenance Manual

INST

ALLER

The wet surfaces of steam enclosures 

may be slippery. Use care when entering or leaving. To 
prevent slip and fall hazards non-slip strips or non-slip 
flooring must be installed on the steam room floor. 

The steamhead is hot. Do not touch the 

steamhead and avoid the steam near the steamhead. 

The information in this manual should 

be used in conjunction with consultations with an 
architect, designer and contractor in determining 
factors necessary in providing a suitable and safe 
steam room. 

MrSteam steam generators must be 

operated with MrSteam controls and accessories only, 
and are to be installed strictly in accordance with the 
specific instructions contained in this manual and as 
supplied in the manuals provided with the controls or 
accessories. 
 
 
 
 
 
 
 
 
 
 
 
 
 

 This document contains important safety, 

operation and maintenance information. Leave this 
document with the owner. Do not discard this 
document. 

 Consider any controls and accessories 

before installation. Read the Installation and 
Operation Manual of all controls and accessories 
available at www.mrsteam.com. 

 Record the model and serial number of the 

steam generator in the space provided in the table of 
contents of this manual. 

 If acrylic, fiberglass or other non-heat 

resistant materials are used as part of the steam room 
enclosure, consult with the material manufacture and see 
page 10, “Steamhead Installation" for additional details. 

 Carefully inspect the steam generator and 

packaging for shipping damage. In the event of 
shipping damage, please contact the carrier for claim 
information. MrSteam customer service department 
can assist you with any missing or damaged parts. 

 The physical size of the steam generator, 

clearance for plumbing servicing, and its distance from 
the steam room must all be considered before 
installation. 
 

HYPERTHERMIA  

The effects of hyperthermia include: 

a)

Failure to perceive heat. 

b)

Failure to recognize the need to exit the 

steambath. 

c)

Unawareness of impending risk.

 

d)

Fetal damage in pregnant women. 

e)

Physical inability to exit the steambath. 

f)

 Unconsciousness. 

 

The use of alcohol, drugs, or medication can greatly 
increase the risk of hyperthermia.

IMPORTANT SAFETY INFORMATION 

Summary of Contents for mr. steam CX Series



























Reviews: