Federal Signal Corporation QuadraFlare QL64Z3V-LI Installation Manual Download Page 3

1

Safety Message to Installers and Service Personnel  
of Warning Light Equipment

People’s lives depend on your proper installation and servicing of Fed-
eral Signal products. It is important to read and follow all instructions 
shipped with this product. In addition, listed below are some other im-
portant safety instructions and precautions you should follow:

Before Installation or Service

Qualifications

•   To  properly  install  or  service  this  equipment,  you  must  have  a  good 

understanding of automotive mechanical and electrical procedures and 
systems, along with proficiency in the installation and service of safe

-

ty warning equipment. Always refer to the vehicle’s service manuals 
when performing equipment installations on a vehicle.

Light Hazards

•   To be an effective warning device, this product produces bright light 

that can be hazardous to your eyesight when viewed at a close range. 
Do not stare directly into this lighting product at a close range or per

-

manent damage to your eyesight may occur.

•   Do not install the light system in an area that would block, impair or 

blind the driver’s vision. Ensure that the light system is mounted in a 
position that is outside of the driver’s field of vision, so the driver can 
safely operate the vehicle.

•   Federal  Signal  power  supplies  and  light  heads  are  designed  to  work 

together as a system. Combining light heads and a power supply from 
different  manufacturers  may  reduce  the  warning  effectiveness  of  the 
lighting system and may damage the components. You should verify or 
test your combination to ensure the system works together and meets 
federal, state and local standards or guidelines. 

Electrical Hazards

•   Strobe systems present a shock hazard because they use high voltage 

to operate. Do not handle strobe cables, the power supply or bulbs or 
remove the lens while the equipment is connected. Strobe systems can 
also hold their charge even after they have been turned off. After dis

-

connecting  power  to  the  unit,  wait  five  minutes  before  handling  any 
parts of the strobe system.

Summary of Contents for QuadraFlare QL64Z3V-LI














Reviews: