Federal Signal Corporation PA4000 Installation Maintenance And Service Manual Download Page 21

Page: 21 / 21

Getting Technical Support and Service

Installation, Maintenance, and Service Manual

Federal Signal

www.fedsig.com

2645 Federal Signal Drive

University Park, Illinois 60484-3167
www.fedsig.com
Customer Support

Police/Fire-EMS:

800-264-3578 • +1 708 534-3400

Work Truck:

800-824-0254 • +1 708 534-3400

Technical Support

800-433-9132 • +1 708 534-3400

Getting Repair Service

The Federal Signal factory provides technical assistance with any problems that

cannot be handled locally.
Any units returned to Federal Signal for service, inspection, or repair must be

accompanied by a Return Material Authorization (RMA). Obtain a RMA from a local

Distributor or Manufacturer’s Representative.
Provide a brief explanation of the service requested, or the nature of the malfunction.
Address all communications and shipments to the following:
Federal Signal Corporation

Service Department

2645 Federal Signal Drive

University Park, IL 60484-3167

Summary of Contents for PA4000





















Search results

Summary of Contents for PA4000

Reviews:

Related manuals for PA4000

Brands by name

Popular brands

Federal Signal Corporation PA4000, Installation Maintenance And Service Manual

Search results

Summary of Contents for PA4000

Reviews:

Related manuals for PA4000

Brands by name

Popular brands