background image

9

Installation and Maintenance Manual 

Federal Signal

 www.fedsig.com

Safety Messages

Safety Message to Operators of Warning Lights

People’s lives depend on your safe use of our products. Listed 

below are some important safety instructions and precautions 

you should follow:
•  Do not attempt to activate or deactivate the light system 

control while driving in a hazardous situation.

•  Although your warning system is operating properly, it 

may not be completely effective. People may not see or 

heed your warning signal. You must recognize this fact and 

continue to drive cautiously.

•  Situations may occur that obstruct your warning signal when 

natural and man-made objects are between your vehicle 

and others, such as raising your hood or trunk lid. If these 

situations occur, be especially careful.

•  All effective sirens and horns produce loud sounds that may 

cause, in certain situations, permanent hearing loss. You and 

your passengers should consider taking appropriate safety 

precautions such as wearing hearing protection.

•  To be an effective warning device, this product produces 

bright light that can be hazardous to your eyesight when 

viewed at a close range. Do not stare directly into this 

lighting product at a close range, or permanent damage to 

your eyesight may occur.

•  The effectiveness of an interior mounted warning light 

depends on the clarity, the tinting, and the angle of the glass 

it is being placed behind. Tinting, dirt, defects and steeply 

angled glass reduce the light output of the warning light. This 

may reduce the effectiveness of the light as a warning signal. 

If your vehicle has dirty, tinted, or steeply angled glass, use 

extra caution when driving your vehicle or blocking the right 

of way with your vehicle.

•  It is important that you fully understand how to safely operate 

this warning system before use.

Summary of Contents for IPX6 IMPAXX





























Reviews: