background image

26    

IMPAXX

®

 IPX600 Series LED Light Heads 

Federal Signal

 www.fedsig.com

Testing the System

Testing the System

SOUND HAZARD: All effective sirens and horns produce loud 

sounds (120 dB) that may cause permanent hearing loss. Always 

minimize your exposure to siren sounds and wear hearing 

protection. Do not sound the siren indoors or in enclosed areas 

where you and others will be exposed to the sound.

LIGHT HAZARD: To be an effective warning device, an 

emergency warning system produces bright light that can be 

hazardous to your eyesight when viewed at a close range. Do 

not stare directly into this lighting product at a close range, or 

permanent damage to your eyesight may occur.

After the installation, test the emergency warning system 

to ensure that it is operating properly. Also test all vehicle 

functions, including horn operation, vehicle safety functions, 

and vehicle lighting systems to ensure proper operation. Ensure 

that the installation has not affected the vehicle operation or 

changed any vehicle safety functions or circuits. 
After testing is complete, provide a copy of these instructions to 

the instructional staff and all operating personnel.
Do not test the sound and light system of the vehicle while 

driving. Operating the vehicle warning systems may pose a 

hazard to the operator and other drivers if the systems do 

not function as expected. Test the vehicle only in a controlled 

environment.

Getting Technical Support and Service

For technical support and service, please contact:

Service Department

Federal Signal Corporation

Phone: 1-800-433-9132 

Email: [email protected] 

Summary of Contents for IPX6 IMPAXX





























Reviews: