background image

2

Federal Signal

 signaling.fedsig.com

Body Construction

GE VALOX

 357 engineering polymer

Faceplate

Steel, corrosion protected and powder coated

Dimensions (H X W X D)

12 X 9.6 X 3.9 inches (305 x 245 x 99 mm)

Net Weight Including Mounting Plate

7 lb (3.2 kg)

Shipping Dimensions

15 X 11.5 X 5 inches (381 x 293 x 127 mm)

Shipping Weight Including Mounting Plate

8 lb (3.7 kg)

Handset Material

High impact ABS

Standard Mounting

Vertical wall

Wiring Access

7/8

"

 opening for owner-supplied fitting

Hardware Material

Stainless steel

 Table 2  

A-Compliance

FCC

Part 15, Class A

ICES-003

Class A

IEC

61000-6-2: 2005 

60950-1

CISPR

22: 2008

Weatherproof Enclosure

Type 3R

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device 

may not cause harmful interference, and (2) this device must accept any interference received, including interference 

that may cause undesired operation.

GENERAL: 

The Federal Signal FT100C-V telephone is designed to provide safe, reliable communication in areas prone to 

high humidity, chemical vapors, dust, and physical abuse. 
The FT100C-V Telephone is compatible with most SIP-based IP PBX servers that comply with SIP RFC 3261. Users can 

remotely monitor and program settings through a web browser to configure telephones on their network.

Features

• 

Enclosure

•  VALOX

 body construction

•  Weather and corrosion resistant
•  Spring-loaded hinged door

• 

Temperature range -22˚ to +140˚F ( -30˚ to +60˚C)

• 

12-key teleseal keypad

• 

Waterproof connections and stainless steel fittings for longer life

• 

Corrosion protected and powder coated steel faceplate

• 

Magnetic reed hook switch — no moving parts

• 

Easily mounted on any sturdy, vertical structure

• 

Noise reducing microphone allows a high level of intelligibility in locations with high background noise

• 

Heavy duty K-type industrial handset

• 

Handset retainers to maintain on-hook status

• 

Modular parts for easy service

• 

Compatible with inductively coupled hearing aid devices

• 

Adaptive full duplex operation

• 

Compatible with most SIP-based IP PBX servers that comply with SIP (RFC 3261)

• 

Network web management interface

• 

The discovery utility makes it easy to detect, locate, and launch the web-based configuration screens

Summary of Contents for FT100C-V













Reviews: