background image

601 Old Airport Road • Bristol, VA 24201   Phone (276) 669-4084 • FAX (276) 669-1869 • www.federalpacific.com • ISO9001:2015

SECTION IB-2D-700

INSTALLATION & OPERATION INSTRUCTIONS

PMDF PAD-MOUNTED SWITCHGEAR 

NOVEMBER 2017 VER. 2.1

PAGE 2

SAFETY INFORMATION

Understanding Safety-Alert Messages

There are several types of safety-alert messages which may 

appear throughout this instruction bulletin as well as on labels 

attached to the pad-mounted switchgear. Familiarize yourself 

with these types of messages and the importance of the various 

signal words, as explained below.

If you do not understand any portion of this instruction bulletin 

and need assistance, contact the Switchgear Division of Federal 

Pacific at 276-669-4084.

Replacement Instructions & Labels

If you need additional copies of this instruction bulletin, contact 

Federal Pacific at 276-669-4084. 
It is important that any missing, damaged, or faded labels on the 

equipment be replaced immediately. Replacement labels are 

available by contacting Federal Pacific.

SAFETY PRECAUTION

FOLLOWING SAFETY INSTRUCTIONS

NOTICE

Thoroughly and carefully read this instruction 

bulletin before installation of the pad-mounted 

switchgear, before switching with elbows or 

installing or accessing the metering transformers 

in this equipment, and before performing any 

maintenance on the equipment.

......

DANGER

Federal Pacific Fuse Mountings in conjunction with appropri-

ate fuses are designed to protect equipment and to disconnect 

faulted equipment from the system. The fuses cannot protect 

personnel from injury or electrocution if contact is made with 

energized circuits or hardware.

NOTICE

NOTICE is used to address practices not related to physical 

injury .

SAFETY 

INSTRUCTIONS

Safety Instructions (or equivalent) signs indicate specific safety-

related instructions or procedures .

DANGER indicates a hazardous situation which, if not avoided, 

will result in death or serious injury .

DANGER

WARNING

WARNING indicates a hazardous situation which, if not avoided, 

could result in death or serous injury .

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, 

could result in minor or moderate injury .

Summary of Contents for PMDF Series













Reviews: